Cat. No. 31-3042
Audio/Video
Receiver
STAV-3770
DOLBY SURROUND
P
R
O
L
O
G
I
C
STAV-3770 AUDIO/VIDEO RECEIVER
STANDBY
POWER
DSP
MODE
DOLBY
VIRTUAL
MEMORY FM MONO CLASS
VOLUME
DSP
DIGITAL
SIGNAL
PROCESSOR
DOLBY
PRO LOGIC
SELECT
LOUDNESS
STATION
TUNING
OSR
DSP
SELECT
TONE
DOWN
LEFT
UP
VCR
TAPE 1
TAPE 2
MONITOR
DVD/LD
CD
FM/AM
PHONO
BALANCE
RIGHT
SPEAKER
4X100WATT
EQUAL POWER OUTPUT
MIN
MAX
PHONES
Owner’s Manual
Please read before using this equipment.
Introducing the Optimus STAV-3770
Your Optimus STAV-3770 Audio/Video Receiver is the perfect control center for
your audio/video system. It combines 100 watts-per-channel of clean power
with modern styling. And, it provides connections for one tape deck, one audio/
video source, one more tape deck or audio/video playback source, a turntable,
a CD player, and a video monitor.
Your receiver also has special sound options. Dolby Pro Logic‘ Surround Sound
delivers movie theater sound for audio/video programs (especially those
encoded with Dolby Surround Sound signals). Dolby 3CH Logic provides a
wider sound field than ordinary playback. DSP Effects creates a listening envi-
ronment that simulates a concert hall, jazz club, theater, or a dance hall. Dolby
Virtual provides a three-dimensional sound field using only the front left and
right speakers.
Additional features include:
Digital-Synthesized Tuner Precisely tunes to AM and FM stations.
30 Memory Locations Let you store and recall the frequencies for up to 30 AM/FM stations.
Automatic Tuning Searches for the next available AM/FM station.
Tape Monitoring Lets you listen to the actual recording as you record, if your tape deck has a
tape-monitoring feature.
Built-In Protection Circuits Automatically turn off the receiver to help avoid power surges or short circuit
damage.
Remote Control Lets you use a single remote control for the receiver and other compatible com-
ponents connected to the receiver.
Note: The remote control requires two AA batteries (not supplied).
We recommend you record the receiver’s serial number here. The number is on the re-
ceiver’s back panel.
Serial Number:_____________________________________________
Note to the Cable TV System Installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the ground-
ing system of the building as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories Licensing Corporation.
Dolby, Pro Logic, and the double-D symbol (
) are trademarks of Dolby Laboratories Licensing Corporation.
1998 Tandy Corporation.
All Rights Reserved.
RadioShack and Optimus are registered trademarks used by Tandy Corporation.
2
Introducing the Optimus STAV-3770
Your Optimus STAV-3770 Audio/Video Receiver is the perfect control center for
your audio/video system. It combines 100 watts-per-channel of clean power
with modern styling. And, it provides connections for one tape deck, one audio/
video source, one more tape deck or audio/video playback source, a turntable,
a CD player, and a video monitor.
Your receiver also has special sound options. Dolby Pro Logic‘ Surround Sound
delivers movie theater sound for audio/video programs (especially those
encoded with Dolby Surround Sound signals). Dolby 3CH Logic provides a
wider sound field than ordinary playback. DSP Effects creates a listening envi-
ronment that simulates a concert hall, jazz club, theater, or a dance hall. Dolby
Virtual provides a three-dimensional sound field using only the front left and
right speakers.
Additional features include:
Digital-Synthesized Tuner Precisely tunes to AM and FM stations.
30 Memory Locations Let you store and recall the frequencies for up to 30 AM/FM stations.
Automatic Tuning Searches for the next available AM/FM station.
Tape Monitoring Lets you listen to the actual recording as you record, if your tape deck has a
tape-monitoring feature.
Built-In Protection Circuits Automatically turn off the receiver to help avoid power surges or short circuit
damage.
Remote Control Lets you use a single remote control for the receiver and other compatible com-
ponents connected to the receiver.
Note: The remote control requires two AA batteries (not supplied).
We recommend you record the receiver’s serial number here. The number is on the re-
ceiver’s back panel.
Serial Number:_____________________________________________
Note to the Cable TV System Installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the ground-
ing system of the building as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories Licensing Corporation.
Dolby, Pro Logic, and the double-D symbol (
) are trademarks of Dolby Laboratories Licensing Corporation.
1998 Tandy Corporation.
All Rights Reserved.
RadioShack and Optimus are registered trademarks used by Tandy Corporation.
2
IMPORTANT SAFETY INSTRUCTIONS
This receiver is made and tested to meet exacting
safety standards. It meets both UL and FCC require-
ments
Careful attention is devoted to quality standards in the manufacture of your receiver, and safety is
a major factor in its design. However, safety is also your responsibility.
This section lists important information that will help you properly use and enjoy your receiver and
accessories. Read all the included safety and operating instructions before using your receiver. Fol-
low them closely, and retain them for future reference.
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for
cleaning. Do not use liquid or aerosol cleaners.
Attachments — Do not use attachments/accessories not recommended by the product manufac-
turer, as they might create a hazard.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the
product. Follow the manufacturer's instructions for mounting, and use a recommended mounting
accessory.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION
: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure reli-
able operation, and protect from overheating. Do not block or cover these open-
ings, and do not place the product on a bed, sofa, rug, or other similar surface. Do
not place the product in a built-in bookcase or rack unless it provides proper ven-
tilation as specified by the manufacturer.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the system’s enclosure that might be of
sufficient magnitude to constitute a risk of
electric shock. Do not open the system’s
case.
Power Sources — Operate this product using only the power source indicated on its marking label.
If you are not sure of your home's power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade
wider than the other). This plug will fit in the power outlet only one way. This is a safety feature. If
you cannot insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, con-
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polar-
ized plug. If you need an extension, use a polarized cord.
This symbol is intended to inform you that im-
portant operating and maintenance instruc-
tions are included in the literature
accompanying this system.
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the product.
!
Lightning — For added protection for this product during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from the wall outlet and disconnect the anten-
na or cable system. This will prevent damage to the product due to lightning and power-line surges.
CAUTION
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles,
as this can result in a risk of fire or electric shock.
Power Lines—Locate an outdoor antenna away from
power lines.
Objects and Liquids — Never push objects of any kind into this product through openings, as they
may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Nonuse Periods—Unplug the receiver’s power cord
when you will not use it for extended periods.
Outdoor Antenna Grounding—If an outside antenna
or cable system is connected to the receiver, ground
the antenna or cable system so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 80, provides information about proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See the
example below.
Servicing — Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service person-
nel.
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qual-
ified service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified techni-
cian to restore the product to normal operation.
Antenna
Lead-In
Wire
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
Ground Clamp
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Antenna
Discharge Unit
(NEC Section 810-20)
Electric
Service
Grounding Conductors
(NEC Section 810-21)
Safety Check — Upon completion of service or repairs to this product, ask the service technician
Equipment
to perform safety checks to determine that the product is in proper operating condition.
Grounding Clamps
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended
by the manufacturer.
Power Service Grounding
Electrode System
(NEC Article 250, Part H)
NEC -- National Electrical Code
Heat — The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
3
IMPORTANT SAFETY INSTRUCTIONS
This receiver is made and tested to meet exacting
safety standards. It meets both UL and FCC require-
ments
Careful attention is devoted to quality standards in the manufacture of your receiver, and safety is
a major factor in its design. However, safety is also your responsibility.
This section lists important information that will help you properly use and enjoy your receiver and
accessories. Read all the included safety and operating instructions before using your receiver. Fol-
low them closely, and retain them for future reference.
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for
cleaning. Do not use liquid or aerosol cleaners.
Attachments — Do not use attachments/accessories not recommended by the product manufac-
turer, as they might create a hazard.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the
product. Follow the manufacturer's instructions for mounting, and use a recommended mounting
accessory.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION
: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure reli-
able operation, and protect from overheating. Do not block or cover these open-
ings, and do not place the product on a bed, sofa, rug, or other similar surface. Do
not place the product in a built-in bookcase or rack unless it provides proper ven-
tilation as specified by the manufacturer.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the system’s enclosure that might be of
sufficient magnitude to constitute a risk of
electric shock. Do not open the system’s
case.
Power Sources — Operate this product using only the power source indicated on its marking label.
If you are not sure of your home's power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade
wider than the other). This plug will fit in the power outlet only one way. This is a safety feature. If
you cannot insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, con-
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polar-
ized plug. If you need an extension, use a polarized cord.
This symbol is intended to inform you that im-
portant operating and maintenance instruc-
tions are included in the literature
accompanying this system.
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the product.
!
Lightning — For added protection for this product during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from the wall outlet and disconnect the anten-
na or cable system. This will prevent damage to the product due to lightning and power-line surges.
CAUTION
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles,
as this can result in a risk of fire or electric shock.
Power Lines—Locate an outdoor antenna away from
power lines.
Objects and Liquids — Never push objects of any kind into this product through openings, as they
may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Nonuse Periods—Unplug the receiver’s power cord
when you will not use it for extended periods.
Outdoor Antenna Grounding—If an outside antenna
or cable system is connected to the receiver, ground
the antenna or cable system so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 80, provides information about proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See the
example below.
Servicing — Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service person-
nel.
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qual-
ified service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified techni-
cian to restore the product to normal operation.
Antenna
Lead-In
Wire
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
Ground Clamp
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Antenna
Discharge Unit
(NEC Section 810-20)
Electric
Service
Grounding Conductors
(NEC Section 810-21)
Safety Check — Upon completion of service or repairs to this product, ask the service technician
Equipment
to perform safety checks to determine that the product is in proper operating condition.
Grounding Clamps
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended
by the manufacturer.
Power Service Grounding
Electrode System
(NEC Article 250, Part H)
NEC -- National Electrical Code
Heat — The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
3
Contents
Preparing Your Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Positioning Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting Program Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using One Remote Control for More than One Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Installing the Remote Control’s Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Using the AC Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Tuning the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using FM MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Adjusting Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Muting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Loudness Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Bypassing the Sound Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Cassette Deck/VCR Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Using the VCR/TAPE 1 and TAPE 2 MONITOR Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Monitoring a Program Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Dubbing a Cassette Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Playing and Recording Video Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Using Advanced Sound Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Sound Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Listening Position for the Dolby Virtual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
The FCC Wants You to Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Index to Features by Control Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4
Contents
Preparing Your Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Positioning Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting Program Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using One Remote Control for More than One Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Installing the Remote Control’s Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Using the AC Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Tuning the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using FM MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Adjusting Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Muting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Loudness Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Bypassing the Sound Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Cassette Deck/VCR Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Using the VCR/TAPE 1 and TAPE 2 MONITOR Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Monitoring a Program Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Dubbing a Cassette Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Playing and Recording Video Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Using Advanced Sound Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Sound Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Listening Position for the Dolby Virtual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
The FCC Wants You to Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Index to Features by Control Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4
Preparing Your Receiver
Caution: Make all the necessary connections before you plug in or turn on the receiver.
Where you place your speakers (not supplied) can make a noticeable difference
in your system’s sound. The guidelines in this section will help you choose the
best locations. After you use your receiver for a while, you might want to try dif-
ferent locations for your speakers.
Positioning Speakers
a
L
R
Bass response depends largely on speaker location. For strong bass, place the
speakers in the corners of the room. If you want even stronger bass, place the
speakers directly on the floor. If the bass is too strong, move the speakers
slightly away from the corners of the room, or raise them 6 to 18 inches off the
floor. You can buy speaker stands at your local RadioShack store.
Midway Point
Between Speakers
b
a = b
The distance between the speakers should be about the same as the distance
between the normal listening point and the point halfway between the speakers.
If you place the speakers too close together, you reduce the stereo separation.
If you place them too far apart, you reduce the bass effect and create a hole in
the middle of the sound.
Normal ListeningPoint
Most speakers have a tweeter dispersion angle of about 60 degrees. Ideally,
your listening position should be just inside the overlap area of the tweeter dis-
persion. You can angle the speakers toward you for better stereo effect.
• Surround speakers generally sound
best if you position them above ear
level.
• To avoid interference with the picture
on a nearby TV, use magnetically
shielded speaker systems. This is par-
ticularly important for the center
speaker since it is usually located
closest to the TV.
To position your speakers for surround sound, place the front speakers at the
front of your listening area, and place the (rear) surround speakers behind or to
the sides of the listening point (see “Using Advanced Sound Options” on
Page 21). Also, place the center speaker above, below, or behind the TV.
Sound might not appear to coincide with the picture if you place it beside the TV.
TV
Front Left
Speaker
Front Right
Speaker
Center Speaker
Front
Listening
Area
Rear
Rear Left
Speaker
Rear Right
Speaker
5
Preparing Your Receiver
Caution: Make all the necessary connections before you plug in or turn on the receiver.
Where you place your speakers (not supplied) can make a noticeable difference
in your system’s sound. The guidelines in this section will help you choose the
best locations. After you use your receiver for a while, you might want to try dif-
ferent locations for your speakers.
Positioning Speakers
a
L
R
Bass response depends largely on speaker location. For strong bass, place the
speakers in the corners of the room. If you want even stronger bass, place the
speakers directly on the floor. If the bass is too strong, move the speakers
slightly away from the corners of the room, or raise them 6 to 18 inches off the
floor. You can buy speaker stands at your local RadioShack store.
Midway Point
Between Speakers
b
a = b
The distance between the speakers should be about the same as the distance
between the normal listening point and the point halfway between the speakers.
If you place the speakers too close together, you reduce the stereo separation.
If you place them too far apart, you reduce the bass effect and create a hole in
the middle of the sound.
Normal ListeningPoint
Most speakers have a tweeter dispersion angle of about 60 degrees. Ideally,
your listening position should be just inside the overlap area of the tweeter dis-
persion. You can angle the speakers toward you for better stereo effect.
• Surround speakers generally sound
best if you position them above ear
level.
• To avoid interference with the picture
on a nearby TV, use magnetically
shielded speaker systems. This is par-
ticularly important for the center
speaker since it is usually located
closest to the TV.
To position your speakers for surround sound, place the front speakers at the
front of your listening area, and place the (rear) surround speakers behind or to
the sides of the listening point (see “Using Advanced Sound Options” on
Page 21). Also, place the center speaker above, below, or behind the TV.
Sound might not appear to coincide with the picture if you place it beside the TV.
TV
Front Left
Speaker
Front Right
Speaker
Center Speaker
Front
Listening
Area
Rear
Rear Left
Speaker
Rear Right
Speaker
5
Preparing Your Receiver
Connecting Speakers
Preparing the Speaker Wires
Speaker wire consists of two conductors (individual wires) encased in insulation
and is usually color-coded or marked with a ridge along one side so you can
identify each conductor. Use these markings as a guide to help you properly
connect the speakers to your receiver.
Follow these guidelines when you select
and connect speakers.
• Only connect speakers that are rated
at between 8 and 16 Ohms.
Follow these steps to prepare the speaker wires.
• Be sure you properly connect all
speakers.
Wire Strands
• Do not connect two pairs of speakers
to a single set of terminals at the
same time.
Speaker Wire
• Realistic, Optimus, and other high-
quality speakers have color-coded
speaker terminals (red for positive po-
larity and black for negative polarity).
Use these color-coded terminals as a
guide to help you properly connect the
speakers to the receiver.
Wire Strands
Conductor
• Use 16-gauge (or larger) speaker wire
for all speaker connections, and con-
sider possible speaker locations be-
fore you decide how much speaker
wire you need.
1. Cut the speaker wires to the necessary length.
2. Separate the wires about 4 inches on each end.
3
3. Using a wire stripper, carefully strip about /4 inch of insulation from the
end of each conductor.
4. Twist the end of each conductor to secure any loose wire strands.
6
Preparing Your Receiver
Connecting Speakers
Preparing the Speaker Wires
Speaker wire consists of two conductors (individual wires) encased in insulation
and is usually color-coded or marked with a ridge along one side so you can
identify each conductor. Use these markings as a guide to help you properly
connect the speakers to your receiver.
Follow these guidelines when you select
and connect speakers.
• Only connect speakers that are rated
at between 8 and 16 Ohms.
Follow these steps to prepare the speaker wires.
• Be sure you properly connect all
speakers.
Wire Strands
• Do not connect two pairs of speakers
to a single set of terminals at the
same time.
Speaker Wire
• Realistic, Optimus, and other high-
quality speakers have color-coded
speaker terminals (red for positive po-
larity and black for negative polarity).
Use these color-coded terminals as a
guide to help you properly connect the
speakers to the receiver.
Wire Strands
Conductor
• Use 16-gauge (or larger) speaker wire
for all speaker connections, and con-
sider possible speaker locations be-
fore you decide how much speaker
wire you need.
1. Cut the speaker wires to the necessary length.
2. Separate the wires about 4 inches on each end.
3
3. Using a wire stripper, carefully strip about /4 inch of insulation from the
end of each conductor.
4. Twist the end of each conductor to secure any loose wire strands.
6
Preparing Your Receiver
Right
Front Speakers
Center Speaker
Left
AUDIO
IN
FRONT SEAKERS
SUB
R
L
WOOFER
CAUTION: SPEAKER IMPEDANCE
8
~ 16 / SPEAKER
PRE
OUT
R
R
L
L
Amplified
Subwoofer
CENTER
SURROUND
SPEAKERS
SPEAKER
Right
Surround Speakers
Left
Connecting the Front Speakers
Note: Be sure you connect the re-
ceiver’s right and left positive (+) and
negative (–) terminals to the speaker’s
corresponding right and left positive (+)
and negative (–) terminals.
Follow these steps to connect the right speaker to the receiver’s right FRONT
SPEAKERS terminals.
1. Press open the receiver’s FRONT SPEAKERS R (+) red lever and insert the
ridged or color-coded conductor’s end into the small hole. Press the lever
closed to secure the conductor.
2. Press open the receiver’s FRONT SPEAKERS R (–) black lever and insert the
other conductor’s end into the small hole. Press the lever closed to
secure the conductor.
3. Connect the ridged or color-coded conductor’s loose end to the right
speaker’s positive (+) terminal.
4. Connect the remaining loose conductor to the right speaker’s negative (–)
terminal.
Repeat Steps 1–4 to connect the left speaker to the receiver’s FRONT SPEAKERS
left terminals.
7
Preparing Your Receiver
Right
Front Speakers
Center Speaker
Left
AUDIO
IN
FRONT SEAKERS
SUB
R
L
WOOFER
CAUTION: SPEAKER IMPEDANCE
8
~ 16 / SPEAKER
PRE
OUT
R
R
L
L
Amplified
Subwoofer
CENTER
SURROUND
SPEAKERS
SPEAKER
Right
Surround Speakers
Left
Connecting the Front Speakers
Note: Be sure you connect the re-
ceiver’s right and left positive (+) and
negative (–) terminals to the speaker’s
corresponding right and left positive (+)
and negative (–) terminals.
Follow these steps to connect the right speaker to the receiver’s right FRONT
SPEAKERS terminals.
1. Press open the receiver’s FRONT SPEAKERS R (+) red lever and insert the
ridged or color-coded conductor’s end into the small hole. Press the lever
closed to secure the conductor.
2. Press open the receiver’s FRONT SPEAKERS R (–) black lever and insert the
other conductor’s end into the small hole. Press the lever closed to
secure the conductor.
3. Connect the ridged or color-coded conductor’s loose end to the right
speaker’s positive (+) terminal.
4. Connect the remaining loose conductor to the right speaker’s negative (–)
terminal.
Repeat Steps 1–4 to connect the left speaker to the receiver’s FRONT SPEAKERS
left terminals.
7
Preparing Your Receiver
Connecting Surround-Sound Speakers
You can connect a pair of speakers to the receiver for surround-sound pro-
grams. Follow the steps in “Connecting the Front Speakers” to connect the
speakers to the SURROUND SPEAKERS terminals.
Connecting the Center Speaker
The center speaker gives additional ambience to surround sound. Follow the
steps in “Connecting the Front Speakers” to connect the center speaker to the
CENTER SPEAKER terminals.
Connecting a Subwoofer Amplifier
Your receiver includes a line-level subwoofer output. Connecting a subwoofer to
your system dramatically extends bass response for incredible richness and
depth. When you listen to surround-sound programs, a subwoofer enhances
your home theater experience by realistically re-creating the rumble of an earth-
quake, the bone-jarring percussion of a cannon, and more. To use the sub-
woofer output, simply connect SUBWOOFER PRE OUT to an amplified subwoofer’s
line-level input or to an amplifier to which you have connected a subwoofer.
RadioShack stores sell a variety of suitable subwoofers and amplifiers.
8
Preparing Your Receiver
Connecting Surround-Sound Speakers
You can connect a pair of speakers to the receiver for surround-sound pro-
grams. Follow the steps in “Connecting the Front Speakers” to connect the
speakers to the SURROUND SPEAKERS terminals.
Connecting the Center Speaker
The center speaker gives additional ambience to surround sound. Follow the
steps in “Connecting the Front Speakers” to connect the center speaker to the
CENTER SPEAKER terminals.
Connecting a Subwoofer Amplifier
Your receiver includes a line-level subwoofer output. Connecting a subwoofer to
your system dramatically extends bass response for incredible richness and
depth. When you listen to surround-sound programs, a subwoofer enhances
your home theater experience by realistically re-creating the rumble of an earth-
quake, the bone-jarring percussion of a cannon, and more. To use the sub-
woofer output, simply connect SUBWOOFER PRE OUT to an amplified subwoofer’s
line-level input or to an amplifier to which you have connected a subwoofer.
RadioShack stores sell a variety of suitable subwoofers and amplifiers.
8
Preparing Your Receiver
You can connect up to five external program sources to your receiver.
Connecting
Program Sources
VIDEO
OUT
TO MONITOR TV
VIDEO
OUT
CONTROL
SUB
WOOFER
OUT
VIDEO
IN
VIDEO
IN
PRE
OUT
IN
PLAY
OUT
REC
IN
PLAY
OUT
REC
IN
IN
IN
L
L
L
R
R
R
TAPE2
MONITOR
CD
VCR/
TAPE1
PHONO
DVD/
LD
SIGNAL GND
LINE
REC
PLAY
OUT PUT
L
L
R
REC
PLAY
R
INPUT OUTPUT
CD
Turntable
Cassette Deck
CD Player
Connecting a Turntable
Connect a turntable with a magnetic cartridge only. Some older turntables use a
ceramic-type cartridge that does not work with this system.
Note: Use shielded audio cables with
phono connectors for all audio connec-
tions.
L
R
Connect the turntable’s left and right cables to the receiver’s (left) and (right)
PHONO IN
SIG-
jacks. Then connect the turntable’s ground wire to the receiver’s
terminal.
NAL GND
Connecting a CD Player
To connect a CD player to the receiver, connect the CD player’s left and right
L
R CD IN
jacks.
output jacks to the receiver’s and
Connecting Cassette Decks
VCR/TAPE 1
TAPE 2 MONITOR
jacks.
You can connect cassette decks to the
and
Note: If you place the cassette deck di-
rectly above, below, or to the left of the
receiver, the receiver could interfere with
the cassette deck’s operation. If possi-
ble, position the cassette deck to the
right or away from the receiver.
VCR/TAPE 1 IN PLAY
TAPE 2
or
Connect the cassette deck’s output jacks to the
MONITOR IN PLAY
VCR/
jacks, and connect the cassette deck’s input jacks to the
TAPE 2 MONITOR OUT REC
jacks.
TAPE 1 OUT REC
or
DVD/LD IN
You can connect a third cassette deck (for playback only) to the
(audio) jacks.
9
Preparing Your Receiver
You can connect up to five external program sources to your receiver.
Connecting
Program Sources
VIDEO
OUT
TO MONITOR TV
VIDEO
OUT
CONTROL
SUB
WOOFER
OUT
VIDEO
IN
VIDEO
IN
PRE
OUT
IN
PLAY
OUT
REC
IN
PLAY
OUT
REC
IN
IN
IN
L
L
L
R
R
R
TAPE2
MONITOR
CD
VCR/
TAPE1
PHONO
DVD/
LD
SIGNAL GND
LINE
REC
PLAY
OUT PUT
L
L
R
REC
PLAY
R
INPUT OUTPUT
CD
Turntable
Cassette Deck
CD Player
Connecting a Turntable
Connect a turntable with a magnetic cartridge only. Some older turntables use a
ceramic-type cartridge that does not work with this system.
Note: Use shielded audio cables with
phono connectors for all audio connec-
tions.
L
R
Connect the turntable’s left and right cables to the receiver’s (left) and (right)
PHONO IN
SIG-
jacks. Then connect the turntable’s ground wire to the receiver’s
terminal.
NAL GND
Connecting a CD Player
To connect a CD player to the receiver, connect the CD player’s left and right
L
R CD IN
jacks.
output jacks to the receiver’s and
Connecting Cassette Decks
VCR/TAPE 1
TAPE 2 MONITOR
jacks.
You can connect cassette decks to the
and
Note: If you place the cassette deck di-
rectly above, below, or to the left of the
receiver, the receiver could interfere with
the cassette deck’s operation. If possi-
ble, position the cassette deck to the
right or away from the receiver.
VCR/TAPE 1 IN PLAY
TAPE 2
or
Connect the cassette deck’s output jacks to the
MONITOR IN PLAY
VCR/
jacks, and connect the cassette deck’s input jacks to the
TAPE 2 MONITOR OUT REC
jacks.
TAPE 1 OUT REC
or
DVD/LD IN
You can connect a third cassette deck (for playback only) to the
(audio) jacks.
9
Preparing Your Receiver
VIDEO
OUT
TO MONITOR TV
VIDEO
OUT
CONTROL
SUB
WOOFER
OUT
VIDEO
IN
VIDEO
IN
PRE
OUT
IN
PLAY
OUT
REC
IN
PLAY
OUT
REC
IN
IN
IN
L
R
L
R
TAPE2
MONITOR
CD
VCR/
TAPE1
PHONO
DVD/
LD
SIGNAL GND
AUDIO
VIDEO
AUDIO
OUT
VIDEO
OUT
REC
PLAY
VIDEO
IN
OUT
IN
L
L
R
R
REC
PLAY
INPUT OUTPUT
VCR
TV Monitor
DVD/LD Player
VCR
Connecting Video Sources
If you connect two video sources, such as VCRs, laser disc (LD) players, or dig-
ital video disc (DVD) players to your receiver, you can use the receiver to select
each video source. You can also use the receiver to easily record from these
video sources to the source connected to VCR/TAPE 1.
Note: If your VCR is monaural, use a Y-
adapter (available at your local Ra-
dioShack store) to connect the VCR’s
audio output to both the L and R audio in-
puts on the receiver.
Connect phono cables from each video source’s audio outputs to the receiver’s
VCR/TAPE 1 IN PLAY or DVD/LD IN jacks. Then connect phono cables from the
receiver’s VCR/TAPE 1 OUT REC jacks to the source’s audio input jacks.
Connect video cables from each video source’s video outputs to the receiver’s
VCR/TAPE 1 or DVD/LD VIDEO IN jacks. Then connect video cables from the
receiver’s VCR/TAPE 1 VIDEO OUT jack to the source’s video input.
Connecting a Video Monitor
The monitor (or TV with baseband video input) you connect to the VIDEO OUT ter-
minal can monitor any program you connect to the receiver’s VCR/TAPE 1 IN PLAY
or DVD/LD IN jacks. Connect a video cable from the receiver’s VIDEO OUT TO MONI-
TOR TV jack to the monitor’s video input.
10
Preparing Your Receiver
VIDEO
OUT
TO MONITOR TV
VIDEO
OUT
CONTROL
SUB
WOOFER
OUT
VIDEO
IN
VIDEO
IN
PRE
OUT
IN
PLAY
OUT
REC
IN
PLAY
OUT
REC
IN
IN
IN
L
R
L
R
TAPE2
MONITOR
CD
VCR/
TAPE1
PHONO
DVD/
LD
SIGNAL GND
AUDIO
VIDEO
AUDIO
OUT
VIDEO
OUT
REC
PLAY
VIDEO
IN
OUT
IN
L
L
R
R
REC
PLAY
INPUT OUTPUT
VCR
TV Monitor
DVD/LD Player
VCR
Connecting Video Sources
If you connect two video sources, such as VCRs, laser disc (LD) players, or dig-
ital video disc (DVD) players to your receiver, you can use the receiver to select
each video source. You can also use the receiver to easily record from these
video sources to the source connected to VCR/TAPE 1.
Note: If your VCR is monaural, use a Y-
adapter (available at your local Ra-
dioShack store) to connect the VCR’s
audio output to both the L and R audio in-
puts on the receiver.
Connect phono cables from each video source’s audio outputs to the receiver’s
VCR/TAPE 1 IN PLAY or DVD/LD IN jacks. Then connect phono cables from the
receiver’s VCR/TAPE 1 OUT REC jacks to the source’s audio input jacks.
Connect video cables from each video source’s video outputs to the receiver’s
VCR/TAPE 1 or DVD/LD VIDEO IN jacks. Then connect video cables from the
receiver’s VCR/TAPE 1 VIDEO OUT jack to the source’s video input.
Connecting a Video Monitor
The monitor (or TV with baseband video input) you connect to the VIDEO OUT ter-
minal can monitor any program you connect to the receiver’s VCR/TAPE 1 IN PLAY
or DVD/LD IN jacks. Connect a video cable from the receiver’s VIDEO OUT TO MONI-
TOR TV jack to the monitor’s video input.
10
Preparing Your Receiver
In many areas, the supplied indoor AM loop and FM antennas provide satisfac-
tory reception.
Connecting the Antennas
AM Antennas
Assemble the supplied AM antenna’s base by swinging the base in the direction
of the arrow and inserting the antenna’s bottom tabs into the base’s slot. If the
receiver is in a rack or on a shelf and there is no room for the AM loop antenna,
use two screws (not supplied) to mount the base on the wall or another location
as shown.
AM LOOP ANTENNA
Attach the antenna wires to the
(upper two terminals).
and (ground) terminals
Place the antenna on a flat surface and rotate it for the best AM reception.
Notes:
• Keep the AM loop antenna connected even when you use another indoor
antenna or an outdoor AM antenna.
LOOP
ANTENNA
• Ensure that the antenna does not touch the receiver or any other metal
object.
AM
ANTENN
AM Loop
Antenna
• Do not place the antenna near a CD player, a personal computer, or a TV
set.
FM
UNBAL
75
• If the wire between your AM loop antenna and receiver is too short, you
can add extra wire, available at your local RadioShack store.
Outdoor AM Antenna
You can also use a RadioShack shortwave antenna kit (Cat. No. 278-758),
which makes an excellent outdoor AM antenna. Connect the outdoor AM
antenna wire to the receiver’s AM terminal, as shown.
LOOP
ANTENNA
AM
ANTENN
AM Loop
Antenna
FM
UNBAL
75
FM Antennas
FM UNBAL 75
Connect the supplied FM antenna to the
extend it.
Ω terminal as shown, then
Note: For the best results, use 75-ohm
coaxial cable to connect an outdoor an-
tenna to the receiver.
For better FM reception, you can also use a rabbit-ear TV antenna (for indoor
use only). To connect the TV antenna to the receiver, you need a VHF/UHF/FM
splitter (not included). RadioShack stores carry a full line of quality antennas
and antenna connection accessories.
LOOP
ANTENNA
AM
ANTENN
FM
UNBAL
75
11
Preparing Your Receiver
In many areas, the supplied indoor AM loop and FM antennas provide satisfac-
tory reception.
Connecting the Antennas
AM Antennas
Assemble the supplied AM antenna’s base by swinging the base in the direction
of the arrow and inserting the antenna’s bottom tabs into the base’s slot. If the
receiver is in a rack or on a shelf and there is no room for the AM loop antenna,
use two screws (not supplied) to mount the base on the wall or another location
as shown.
AM LOOP ANTENNA
Attach the antenna wires to the
(upper two terminals).
and (ground) terminals
Place the antenna on a flat surface and rotate it for the best AM reception.
Notes:
• Keep the AM loop antenna connected even when you use another indoor
antenna or an outdoor AM antenna.
LOOP
ANTENNA
• Ensure that the antenna does not touch the receiver or any other metal
object.
AM
ANTENN
AM Loop
Antenna
• Do not place the antenna near a CD player, a personal computer, or a TV
set.
FM
UNBAL
75
• If the wire between your AM loop antenna and receiver is too short, you
can add extra wire, available at your local RadioShack store.
Outdoor AM Antenna
You can also use a RadioShack shortwave antenna kit (Cat. No. 278-758),
which makes an excellent outdoor AM antenna. Connect the outdoor AM
antenna wire to the receiver’s AM terminal, as shown.
LOOP
ANTENNA
AM
ANTENN
AM Loop
Antenna
FM
UNBAL
75
FM Antennas
FM UNBAL 75
Connect the supplied FM antenna to the
extend it.
Ω terminal as shown, then
Note: For the best results, use 75-ohm
coaxial cable to connect an outdoor an-
tenna to the receiver.
For better FM reception, you can also use a rabbit-ear TV antenna (for indoor
use only). To connect the TV antenna to the receiver, you need a VHF/UHF/FM
splitter (not included). RadioShack stores carry a full line of quality antennas
and antenna connection accessories.
LOOP
ANTENNA
AM
ANTENN
FM
UNBAL
75
11
Preparing Your Receiver
For the best radio reception, use an outdoor antenna. Follow these steps to
connect an outdoor FM antenna to the receiver using 75Ω coaxial cable.
Warning: To prevent injury, read and fol-
low all cautions and warnings that ac-
company the outdoor antenna.
Note: If your antenna has 300Ω twin-lead cable, consult your local RadioShack
store for the correct adapter.
1. Disconnect the supplied FM antenna from the receiver’s FM UNBAL 75Ω
terminal.
2. With a stripping tool, remove about 11/2 inches of the outdoor antenna
cable’s outer insulation to expose the cable’s shielding.
3. Fold back the shielding from the inner insulation.
4. Remove about 1 inch of the inner insulation from around the center wire.
Inner Insulation
Center Wire
Outer Insulation
Shielding
5. Pull the shielding to one side. Connect the center wire to the receiver’s FM
UNBAL 75Ω terminal. Twist the shielding to secure any loose wire strands,
and connect it to the FM UNBAL 75Ω terminal.
Caution: The cable’s shielding should
only touch the terminal.
Outdoor FM Antenna
LOOP
ANTENNA
AM
ANTENN
Shielding
FM
UNBAL
75
Center
Wire
Note: Grounding is not necessary for reception, but we recommend it for better
FM reception and to avoid damage from lightning when you use an outdoor FM
antenna. Use a separate piece of thick polyvinyl insulated wire to connect the
terminal to the building’s power service grounding electrode system.
Warning: Never connect a wire to a gas pipe for grounding since sparks might
ignite the gas.
12
Preparing Your Receiver
For the best radio reception, use an outdoor antenna. Follow these steps to
connect an outdoor FM antenna to the receiver using 75Ω coaxial cable.
Warning: To prevent injury, read and fol-
low all cautions and warnings that ac-
company the outdoor antenna.
Note: If your antenna has 300Ω twin-lead cable, consult your local RadioShack
store for the correct adapter.
1. Disconnect the supplied FM antenna from the receiver’s FM UNBAL 75Ω
terminal.
2. With a stripping tool, remove about 11/2 inches of the outdoor antenna
cable’s outer insulation to expose the cable’s shielding.
3. Fold back the shielding from the inner insulation.
4. Remove about 1 inch of the inner insulation from around the center wire.
Inner Insulation
Center Wire
Outer Insulation
Shielding
5. Pull the shielding to one side. Connect the center wire to the receiver’s FM
UNBAL 75Ω terminal. Twist the shielding to secure any loose wire strands,
and connect it to the FM UNBAL 75Ω terminal.
Caution: The cable’s shielding should
only touch the terminal.
Outdoor FM Antenna
LOOP
ANTENNA
AM
ANTENN
Shielding
FM
UNBAL
75
Center
Wire
Note: Grounding is not necessary for reception, but we recommend it for better
FM reception and to avoid damage from lightning when you use an outdoor FM
antenna. Use a separate piece of thick polyvinyl insulated wire to connect the
terminal to the building’s power service grounding electrode system.
Warning: Never connect a wire to a gas pipe for grounding since sparks might
ignite the gas.
12
Preparing Your Receiver
If you also have an Optimus professional series CD player, VCR, or cassette
Using One Remote Control
for More than One Unit
CONTROL IN
deck with the OSR mark ( ), you can connect its
jack to the
receiver so you can control all of your equipment with a single remote control.
You can also use the other component’s remote control by pointing it at the
receiver’s front panel.
Note: When you plug the cable into a
CONTROL IN
component’s
jack, that com-
1. Connect each component to the receiver as shown in “Connecting Pro-
gram Sources” on Page 9.
ponent’s remote sensor does not func-
tion.
Note: You must connect the audio cables between the receiver and the
other audio accessory to use your receiver’s remote control to control the
accessory.
CONTROL
CONTROL
OUT
IN
OUT
2. Connect the cable supplied with the CD player, VCR, or cassette deck to
CONTROL OUT
CONTROL IN
jack and the other component’s
the receiver’s
jack.
3. When you want to control more than one other component using the
Other Component
with OSR Mark
Receiver
CONTROL OUT
CONTROL IN
and
receiver’s remote control, daisy-chain the
connections as shown.
To the CONTROL IN Jack
of Another Component
Having the OSR Mark
Remote
Control
The remote control uses two AA batteries (not included). For the longest battery
life, we recommend alkaline batteries (such as RadioShack Cat. No. 23-557).
Installing the
Remote Control’s Batteries
1. Press and slide open the battery compartment cover.
Cautions:
2. Place two fresh AA batteries in the compartment as indicated by the
polarity symbols (+ and –) marked in the compartment.
• Use only fresh batteries of the required
size and recommended type.
• Always remove old or weak batteries.
Batteries can leak chemicals that can
damage electronic circuits.
3. Replace the battery compartment cover.
Note: If the remote’s range is reduced,
replace the batteries.
13
Preparing Your Receiver
If you also have an Optimus professional series CD player, VCR, or cassette
Using One Remote Control
for More than One Unit
CONTROL IN
deck with the OSR mark ( ), you can connect its
jack to the
receiver so you can control all of your equipment with a single remote control.
You can also use the other component’s remote control by pointing it at the
receiver’s front panel.
Note: When you plug the cable into a
CONTROL IN
component’s
jack, that com-
1. Connect each component to the receiver as shown in “Connecting Pro-
gram Sources” on Page 9.
ponent’s remote sensor does not func-
tion.
Note: You must connect the audio cables between the receiver and the
other audio accessory to use your receiver’s remote control to control the
accessory.
CONTROL
CONTROL
OUT
IN
OUT
2. Connect the cable supplied with the CD player, VCR, or cassette deck to
CONTROL OUT
CONTROL IN
jack and the other component’s
the receiver’s
jack.
3. When you want to control more than one other component using the
Other Component
with OSR Mark
Receiver
CONTROL OUT
CONTROL IN
and
receiver’s remote control, daisy-chain the
connections as shown.
To the CONTROL IN Jack
of Another Component
Having the OSR Mark
Remote
Control
The remote control uses two AA batteries (not included). For the longest battery
life, we recommend alkaline batteries (such as RadioShack Cat. No. 23-557).
Installing the
Remote Control’s Batteries
1. Press and slide open the battery compartment cover.
Cautions:
2. Place two fresh AA batteries in the compartment as indicated by the
polarity symbols (+ and –) marked in the compartment.
• Use only fresh batteries of the required
size and recommended type.
• Always remove old or weak batteries.
Batteries can leak chemicals that can
damage electronic circuits.
3. Replace the battery compartment cover.
Note: If the remote’s range is reduced,
replace the batteries.
13
Preparing Your Receiver
Using the AC Power Outlet
Your receiver has an AC power outlet that you can use to power an electronic
device, such as a turntable, cassette deck, VCR, and so on. This switched out-
let turns on and off with the receiver and provides a maximum of 100 Watts.
Caution: Do not connect appliances with
high power consumption, such as a
heater, iron, monitor, or TV, to this AC
outlet. Doing so can cause a risk of over-
heating and fire, and could damage the
receiver.
B
F
CAUTION: SPEAKER IMPEDANCE
~ 16 / SPEAKER
8
AC OUTLT
AC 120V 60Hz
CAUTION:
DO NOT CONNECT
TV SET OR MONITOR.
SWITCHED
100W MAX
0.8A MAX
SURROUND
SPEAKERS
Before you plug in the receiver’s power cord, double check all other connec-
tions.
Connecting to AC Power
To power the receiver, plug the supplied power cord into a standard AC outlet.
The power cord’s plug is polarized and fits only one way.
Warning: To prevent electric shock, do
not use this polarized plug with an exten-
sion cord, receptacle, or other outlet un-
less you can fully insert the blades to
prevent blade exposure.
CAUTION: SPEAKER IMPEDANCE
~ 16 / SPEAKER
8
AC OUTLT
AC 120V 60Hz
CAUTION:
DO NOT CONNECT
TV SET OR MONITOR.
SWITCHED
100W MAX
0.8A MAX
SURROUND
SPEAKERS
S
14
Preparing Your Receiver
Using the AC Power Outlet
Your receiver has an AC power outlet that you can use to power an electronic
device, such as a turntable, cassette deck, VCR, and so on. This switched out-
let turns on and off with the receiver and provides a maximum of 100 Watts.
Caution: Do not connect appliances with
high power consumption, such as a
heater, iron, monitor, or TV, to this AC
outlet. Doing so can cause a risk of over-
heating and fire, and could damage the
receiver.
B
F
CAUTION: SPEAKER IMPEDANCE
~ 16 / SPEAKER
8
AC OUTLT
AC 120V 60Hz
CAUTION:
DO NOT CONNECT
TV SET OR MONITOR.
SWITCHED
100W MAX
0.8A MAX
SURROUND
SPEAKERS
Before you plug in the receiver’s power cord, double check all other connec-
tions.
Connecting to AC Power
To power the receiver, plug the supplied power cord into a standard AC outlet.
The power cord’s plug is polarized and fits only one way.
Warning: To prevent electric shock, do
not use this polarized plug with an exten-
sion cord, receptacle, or other outlet un-
less you can fully insert the blades to
prevent blade exposure.
CAUTION: SPEAKER IMPEDANCE
~ 16 / SPEAKER
8
AC OUTLT
AC 120V 60Hz
CAUTION:
DO NOT CONNECT
TV SET OR MONITOR.
SWITCHED
100W MAX
0.8A MAX
SURROUND
SPEAKERS
S
14
Basic Operation
The controls on the remote control work the same as the buttons on the
receiver’s front panel, though some are labeled differently.
Warning: To prevent possible hearing
loss, turn VOLUME to MIN before you turn
on the receiver or change the program
sources. After you turn on the receiver or
change the program source, adjust VOL-
UME to a comfortable listening level.
Follow these steps to use the receiver.
1. Press POWER to turn on the receiver’s power. It takes about 5 seconds to
begin hearing sound.
2. Press SPEAKER on the left front of the receiver (if necessary) so SP A
appears on the upper left portion of the display.
3. Select a program source.
To tune to a radio station, see “Tuning the Radio” on Page 16.
To listen to signals from the component connected to TAPE 2 MONITOR,
press TAPE 2 MONITOR so TAPE2appears on the display.
Note: If you select a source while TAPE 2
MONITOR is engaged, TAPE 2 flashes
five times on the display, reminding you
to disengage the TAPE 2 MONITOR func-
tion.
To listen to a source other than one connected to TAPE 2 MONITOR, be sure
TAPE2does not show on the display. If necessary, press TAPE 2 MONITOR
so TAPE2disappears. Then press VCR/TAPE 1, DVD/LD (digital video disc/
laser disc), CD, AM/FM (tuner), or PHONO, or repeatedly press FUNC on the
remote control, to display the desired program source.
4. Adjust VOLUME clockwise to increase the volume or counterclockwise to
decrease it. Or, you can use MASTER VOLUME –/+ on the remote control.
5. Adjust the bass, treble, or balance to suit your listening preference.
Repeatedly press TONE/BALANCE on the front of the receiver until the item
you want to adjust appears on the display — TREB., BASS, or BAL-
ANCE. Then press DOWN/LEFT or UP/RIGHT until you get the desired sound.
For more detail on adjusting the sound balance, see “Adjusting Balance”
on Page 17.
6. When you finish using the receiver, press POWER to turn it off.
Note: To find out what a particular button
or control is used for, see Page 24 (for
the remote control) or Page 31 (for the
front panel) to find the page where the
button or control is described.
15
Basic Operation
The controls on the remote control work the same as the buttons on the
receiver’s front panel, though some are labeled differently.
Warning: To prevent possible hearing
loss, turn VOLUME to MIN before you turn
on the receiver or change the program
sources. After you turn on the receiver or
change the program source, adjust VOL-
UME to a comfortable listening level.
Follow these steps to use the receiver.
1. Press POWER to turn on the receiver’s power. It takes about 5 seconds to
begin hearing sound.
2. Press SPEAKER on the left front of the receiver (if necessary) so SP A
appears on the upper left portion of the display.
3. Select a program source.
To tune to a radio station, see “Tuning the Radio” on Page 16.
To listen to signals from the component connected to TAPE 2 MONITOR,
press TAPE 2 MONITOR so TAPE2appears on the display.
Note: If you select a source while TAPE 2
MONITOR is engaged, TAPE 2 flashes
five times on the display, reminding you
to disengage the TAPE 2 MONITOR func-
tion.
To listen to a source other than one connected to TAPE 2 MONITOR, be sure
TAPE2does not show on the display. If necessary, press TAPE 2 MONITOR
so TAPE2disappears. Then press VCR/TAPE 1, DVD/LD (digital video disc/
laser disc), CD, AM/FM (tuner), or PHONO, or repeatedly press FUNC on the
remote control, to display the desired program source.
4. Adjust VOLUME clockwise to increase the volume or counterclockwise to
decrease it. Or, you can use MASTER VOLUME –/+ on the remote control.
5. Adjust the bass, treble, or balance to suit your listening preference.
Repeatedly press TONE/BALANCE on the front of the receiver until the item
you want to adjust appears on the display — TREB., BASS, or BAL-
ANCE. Then press DOWN/LEFT or UP/RIGHT until you get the desired sound.
For more detail on adjusting the sound balance, see “Adjusting Balance”
on Page 17.
6. When you finish using the receiver, press POWER to turn it off.
Note: To find out what a particular button
or control is used for, see Page 24 (for
the remote control) or Page 31 (for the
front panel) to find the page where the
button or control is described.
15
Basic Operation
Tuning the Radio
Your receiver has four types of electronic tuning — manual, automatic, direct
access, and memory.
Manual and Automatic Tuning
Note: For weak signals, we recommend
manual tuning.
Follow these steps to manually or automatically tune to stations.
Hint: If none of the tuning buttons on the remote control operate, press TUNER
first.
FM/AM BAND
1. Press
(
on the remote control) to select the tuner. Then press
FM/AM BAND
(
) again to select the desired band. The receiver tunes to and
displays the frequency last selected in that band.
If A, B, or Cand a single digit number appear to the left of the station fre-
SELECT BAND
quency, press
(
on the remote control) so the band name (AM
or FM) appears.
TUNING
2. To manually select the next lower or higher frequency, press
(
FREQ
on the remote control) once to manually select the next lower or
higher frequency. Or, hold down the button to rapidly change frequencies,
and release it.
To automatically search for the next lower or higher station, hold down
TUNING
FREQ
(
on the remote control) until the display starts to
change, then release it. The receiver searches down or up the band to the
next strong station.
Notes:
• TUNEDappears when you receive a strong signal.
TUNING
TUNING
•
If you press
at the top of the frequency range or
at
the bottom of the frequency range, the display returns to the other
end of the range.
Direct Access Tuning (Remote Control Only)
Follow these steps to directly enter a frequency.
FM/AM BAND
1. Press
(
on the remote control) to select the tuner. Then press
FM/AM BAND
(
) again to select the desired band. The receiver tunes to and
displays the frequency last selected in that band.
DIRECT ACCESS
2. Press
. __ __ __ __appears on the display
with the first __flashing.
3. Enter the desired frequency using the number buttons.
Notes:
• If you enter an invalid frequency (for example, entering 828), the receiver
tunes to the closest valid frequency (830 kHz).
• If you do not press a key within 5 seconds, the receiver exits direct access
tuning. Start over at Step2.
16
Basic Operation
Tuning the Radio
Your receiver has four types of electronic tuning — manual, automatic, direct
access, and memory.
Manual and Automatic Tuning
Note: For weak signals, we recommend
manual tuning.
Follow these steps to manually or automatically tune to stations.
Hint: If none of the tuning buttons on the remote control operate, press TUNER
first.
FM/AM BAND
1. Press
(
on the remote control) to select the tuner. Then press
FM/AM BAND
(
) again to select the desired band. The receiver tunes to and
displays the frequency last selected in that band.
If A, B, or Cand a single digit number appear to the left of the station fre-
SELECT BAND
quency, press
(
on the remote control) so the band name (AM
or FM) appears.
TUNING
2. To manually select the next lower or higher frequency, press
(
FREQ
on the remote control) once to manually select the next lower or
higher frequency. Or, hold down the button to rapidly change frequencies,
and release it.
To automatically search for the next lower or higher station, hold down
TUNING
FREQ
(
on the remote control) until the display starts to
change, then release it. The receiver searches down or up the band to the
next strong station.
Notes:
• TUNEDappears when you receive a strong signal.
TUNING
TUNING
•
If you press
at the top of the frequency range or
at
the bottom of the frequency range, the display returns to the other
end of the range.
Direct Access Tuning (Remote Control Only)
Follow these steps to directly enter a frequency.
FM/AM BAND
1. Press
(
on the remote control) to select the tuner. Then press
FM/AM BAND
(
) again to select the desired band. The receiver tunes to and
displays the frequency last selected in that band.
DIRECT ACCESS
2. Press
. __ __ __ __appears on the display
with the first __flashing.
3. Enter the desired frequency using the number buttons.
Notes:
• If you enter an invalid frequency (for example, entering 828), the receiver
tunes to the closest valid frequency (830 kHz).
• If you do not press a key within 5 seconds, the receiver exits direct access
tuning. Start over at Step2.
16
Basic Operation
Memory Tuning
Memory tuning lets you store up to 30 AM or FM frequencies in three different
classes (10 frequencies in each class), then quickly tune to a class and station.
Note: A class is a group of up to 10 sta-
tion frequencies.
Follow these steps to store a station in a memory location using the front panel
controls. (You cannot store a station in a memory using the remote control)
1. Press FM/AM to select the tuner, then press FM/AM again to select the
desired band.
2. Tune to the frequency you want to store.
Notes:
• If you store a frequency in a memory
that already contains a frequency, you
replace the previous frequency.
If desired, press FM MONO for FM stereo or monaural sound (see “Using
FM MONO”). This setting is also stored in memory.
__
3. Press MEMORY. The class (A, B, or C) and
(for the channel number)
• If your receiver is disconnected from
AC power for several days, it loses all
the stored frequencies.
flash on the display for about 5 seconds.
4. Press CLASS until the class you want (A, B, or C) appears, then press STA-
TION or until the channel number you want appears.
In about five seconds, the class and channel number light steadily, indi-
cating the receiver stored the frequency.
To tune to a stored station, press CLASS so the desired class number appears,
then repeatedly press STATION or to select the channel. Or, you can directly
enter the channel number using that number’s key on the remote control.
To receive FM stations in stereo, press FM MONO so MONOdisappears from the
display. STEREOappears when you receive an FM broadcast in stereo.
Using FM MONO
You can improve the reception of weak FM stations by pressing FM MONO until
MONOappears. This reduces noise while you listen to a weak FM station, but
you get monaural instead of stereo sound.
The TONE/BALANCE control lets you adjust the sound balance between the left
and right speakers. If you properly position the speakers and your listening area
is centered between them, the center control setting is usually best (see “Posi-
tioning Speakers” on Page 5).
Adjusting Balance
For an unusual speaker placement, adjust the speaker balance as follows:
1. Press FM/AM to select the tuner, then press FM/AM again to select the FM
band.
2. Press FM MONO so MONOappears. The sound is monaural instead of ste-
reo, so each speaker delivers the same output.
3. Repeatedly press TONE/BALANCE on the front of the receiver until BAL-
ANCEappears. Then press DOWN/LEFT or UP/RIGHT until you hear the
sound coming equally from each speaker when you are in the listening
area.
4. Press FM MONO so MONOdisappears from the display.
17
Basic Operation
Memory Tuning
Memory tuning lets you store up to 30 AM or FM frequencies in three different
classes (10 frequencies in each class), then quickly tune to a class and station.
Note: A class is a group of up to 10 sta-
tion frequencies.
Follow these steps to store a station in a memory location using the front panel
controls. (You cannot store a station in a memory using the remote control)
1. Press FM/AM to select the tuner, then press FM/AM again to select the
desired band.
2. Tune to the frequency you want to store.
Notes:
• If you store a frequency in a memory
that already contains a frequency, you
replace the previous frequency.
If desired, press FM MONO for FM stereo or monaural sound (see “Using
FM MONO”). This setting is also stored in memory.
__
3. Press MEMORY. The class (A, B, or C) and
(for the channel number)
• If your receiver is disconnected from
AC power for several days, it loses all
the stored frequencies.
flash on the display for about 5 seconds.
4. Press CLASS until the class you want (A, B, or C) appears, then press STA-
TION or until the channel number you want appears.
In about five seconds, the class and channel number light steadily, indi-
cating the receiver stored the frequency.
To tune to a stored station, press CLASS so the desired class number appears,
then repeatedly press STATION or to select the channel. Or, you can directly
enter the channel number using that number’s key on the remote control.
To receive FM stations in stereo, press FM MONO so MONOdisappears from the
display. STEREOappears when you receive an FM broadcast in stereo.
Using FM MONO
You can improve the reception of weak FM stations by pressing FM MONO until
MONOappears. This reduces noise while you listen to a weak FM station, but
you get monaural instead of stereo sound.
The TONE/BALANCE control lets you adjust the sound balance between the left
and right speakers. If you properly position the speakers and your listening area
is centered between them, the center control setting is usually best (see “Posi-
tioning Speakers” on Page 5).
Adjusting Balance
For an unusual speaker placement, adjust the speaker balance as follows:
1. Press FM/AM to select the tuner, then press FM/AM again to select the FM
band.
2. Press FM MONO so MONOappears. The sound is monaural instead of ste-
reo, so each speaker delivers the same output.
3. Repeatedly press TONE/BALANCE on the front of the receiver until BAL-
ANCEappears. Then press DOWN/LEFT or UP/RIGHT until you hear the
sound coming equally from each speaker when you are in the listening
area.
4. Press FM MONO so MONOdisappears from the display.
17
Basic Operation
1
To listen with headphones (not supplied), insert the headphones’ /4-inch plug
Using Headphones
PHONES
into the receiver’s front panel
jack. To silence the speakers and listen
SPEAKER
with headphones without disturbing others, press
appears on the display.
so only SP
Listening Safely
To protect your hearing, note the following when using headphones.
• Set the volume to its lowest setting before you begin listening. After you
begin listening, adjust the volume to a comfortable level.
• Do not listen at extremely high volume levels. Extended high-
volume listening can lead to permanent hearing loss.
• Once you set the volume, do not increase it. Over time, your ears adapt to
the volume level, so a volume level that does not cause discomfort might
still damage your hearing.
MUTING
To temporarily mute the sound, press
on the remote control. --MUT-
Muting the Receiver
Loudness Control
MUTING
ING--appears. Press
again to restore the audio level.
To increase the high and low ranges of sounds for improved audio at a low lis-
LOUDNESS
LOUD
tening level, press
appears. Press
(or
on the remote control) so LOUDNESS
LOUDNESS
LOUD
) again to turn off this feature.
(or
BASS TREBLE BALANCE
, or any spe-
cial sound options) so you can hear the audio at its original tonal quality (for
To bypass your receiver’s sound controls (
,
,
Bypassing the Sound
Controls (Remote Control
Only)
DIRECT
example), press
on the remote control so DIRECTappears. Press
DIRECT
again to turn off this feature.
Note: When you turn off the bypass feature, you will have to reselect any
desired special sound options (see “Using Advanced Sound Options” on
Page 21).
18
Basic Operation
1
To listen with headphones (not supplied), insert the headphones’ /4-inch plug
Using Headphones
PHONES
into the receiver’s front panel
jack. To silence the speakers and listen
SPEAKER
with headphones without disturbing others, press
appears on the display.
so only SP
Listening Safely
To protect your hearing, note the following when using headphones.
• Set the volume to its lowest setting before you begin listening. After you
begin listening, adjust the volume to a comfortable level.
• Do not listen at extremely high volume levels. Extended high-
volume listening can lead to permanent hearing loss.
• Once you set the volume, do not increase it. Over time, your ears adapt to
the volume level, so a volume level that does not cause discomfort might
still damage your hearing.
MUTING
To temporarily mute the sound, press
on the remote control. --MUT-
Muting the Receiver
Loudness Control
MUTING
ING--appears. Press
again to restore the audio level.
To increase the high and low ranges of sounds for improved audio at a low lis-
LOUDNESS
LOUD
tening level, press
appears. Press
(or
on the remote control) so LOUDNESS
LOUDNESS
LOUD
) again to turn off this feature.
(or
BASS TREBLE BALANCE
, or any spe-
cial sound options) so you can hear the audio at its original tonal quality (for
To bypass your receiver’s sound controls (
,
,
Bypassing the Sound
Controls (Remote Control
Only)
DIRECT
example), press
on the remote control so DIRECTappears. Press
DIRECT
again to turn off this feature.
Note: When you turn off the bypass feature, you will have to reselect any
desired special sound options (see “Using Advanced Sound Options” on
Page 21).
18
Cassette Deck/VCR Features
You can connect two cassette decks to the receiver. Selecting either VCR/TAPE 1
or TAPE 2 MONITOR lets you hear the playback from the cassette deck you con-
nected to the receiver’s corresponding (VCR/TAPE 1or TAPE 2 MONITOR) jacks.
Press VCR/TAPE 1. VCRappears on the display. You hear the playback from the
cassette deck or VCR you connected to the receiver’s VCR/TAPE 1 IN jacks.
Using the VCR/TAPE 1 and
TAPE 2 MONITOR Buttons
Press TAPE 2 MONITOR. TAPE 2appears on the display along with the last pro-
gram source you selected. You can hear playback or monitor a recording from
the cassette deck you connected to the receiver’s TAPE 2 MONITOR jacks. The
TAPE 2 MONITOR REC jacks continue to output sound from the previously selected
source after you press TAPE 2 MONITOR.
To return to the previous source, press TAPE 2 MONITOR again so TAPE2disap-
pears.
Notes:
• If you press TAPE 2 MONITOR when that cassette deck is neither playing nor
recording, the receiver mutes the current audio source. To hear the audio
source, press TAPE 2 MONITOR so TAPE2disappears from the display.
• Do not press TAPE 2 MONITOR while you are recording on the deck con-
nected to TAPE 2 MONITOR REC. If you do, the recording is interrupted for
about 1 second.
The receiver sends the audio of the program source you select—VCR/TAPE 1,
DVD/LD, CD, FM/AM (tuner), or PHONO—to the VCR/TAPE 1 OUT/REC (audio) and
TAPE 2 MONITOR OUT/REC jacks. If you select VCR/TAPE 1 or DVD/LD, the video pro-
gram is also sent to the VIDEO OUT TO MONITOR TV jack.
Monitoring a
Program Source
The VOLUME control does not affect the level of the signal going to the tape
decks.
You can copy (dub) a cassette tape from one cassette deck to another through
the STAV-3770.
Dubbing a Cassette Tape
You can use either deck as the playback or recording deck. However, if you
want to monitor the cassette deck during dubbing, use the deck connected to
the VCR/TAPE 1 jacks as the source, and the deck you connected to the TAPE 2
REC jacks as the recording deck. Then press TAPE 2 MONITOR so TAPE2and the
last program source you selected appear on the display. See “Using the VCR/
TAPE 1 and TAPE 2 MONITOR Buttons.”
The VOLUME control does not affect the level of the signal going to the tape
decks.
19
Cassette Deck/VCR Features
You can connect two cassette decks to the receiver. Selecting either VCR/TAPE 1
or TAPE 2 MONITOR lets you hear the playback from the cassette deck you con-
nected to the receiver’s corresponding (VCR/TAPE 1or TAPE 2 MONITOR) jacks.
Press VCR/TAPE 1. VCRappears on the display. You hear the playback from the
cassette deck or VCR you connected to the receiver’s VCR/TAPE 1 IN jacks.
Using the VCR/TAPE 1 and
TAPE 2 MONITOR Buttons
Press TAPE 2 MONITOR. TAPE 2appears on the display along with the last pro-
gram source you selected. You can hear playback or monitor a recording from
the cassette deck you connected to the receiver’s TAPE 2 MONITOR jacks. The
TAPE 2 MONITOR REC jacks continue to output sound from the previously selected
source after you press TAPE 2 MONITOR.
To return to the previous source, press TAPE 2 MONITOR again so TAPE2disap-
pears.
Notes:
• If you press TAPE 2 MONITOR when that cassette deck is neither playing nor
recording, the receiver mutes the current audio source. To hear the audio
source, press TAPE 2 MONITOR so TAPE2disappears from the display.
• Do not press TAPE 2 MONITOR while you are recording on the deck con-
nected to TAPE 2 MONITOR REC. If you do, the recording is interrupted for
about 1 second.
The receiver sends the audio of the program source you select—VCR/TAPE 1,
DVD/LD, CD, FM/AM (tuner), or PHONO—to the VCR/TAPE 1 OUT/REC (audio) and
TAPE 2 MONITOR OUT/REC jacks. If you select VCR/TAPE 1 or DVD/LD, the video pro-
gram is also sent to the VIDEO OUT TO MONITOR TV jack.
Monitoring a
Program Source
The VOLUME control does not affect the level of the signal going to the tape
decks.
You can copy (dub) a cassette tape from one cassette deck to another through
the STAV-3770.
Dubbing a Cassette Tape
You can use either deck as the playback or recording deck. However, if you
want to monitor the cassette deck during dubbing, use the deck connected to
the VCR/TAPE 1 jacks as the source, and the deck you connected to the TAPE 2
REC jacks as the recording deck. Then press TAPE 2 MONITOR so TAPE2and the
last program source you selected appear on the display. See “Using the VCR/
TAPE 1 and TAPE 2 MONITOR Buttons.”
The VOLUME control does not affect the level of the signal going to the tape
decks.
19
Cassette Deck/VCR Features
You can connect two video sources to the receiver. If you connect a VCR to the
Playing and Recording
Video Tapes
VCR/TAPE 1
DVD/LD
audio and video jacks, you can copy video cassette
and
tapes from one VCR to another and monitor the dubbing process.
Playing a Video Tape
VCR/TAPE 1
To play a video tape, load the tape into the VCR connected to either
DVD/LD
VCR/TAPE 1
DVD/LD
or ) that corresponds to the jack
or
. Press the button (
the VCR is connected to. VCRor DVD/LDappears on the display. Follow the
VCR’s instructions to begin playback. If you connected a monitor to the
TO MONITOR TV
receiver’s
jack, you can view the program on that monitor.
Copying a Video Tape
Follow these steps to copy a video tape from one VCR to another through the
STAV-3770.
DVD/LD
1. Load the tape you want to copy into the VCR connected to
.
2. Load a blank tape (or one you want to record over) into the VCR con-
VCR/TAPE 1
nected to the
jacks.
DVD/LD
3. Press
.
4. Begin recording and playback on the VCRs.
Important: Most material performed in public, such as concerts, plays, and
movies, or distributed on prerecorded video tapes is copyrighted. The unautho-
rized recording or duplication of copyrighted material is a violation of the copy-
right laws of most countries and such duplication may result in fines,
imprisonment, or both. Note, however, that in the United States, it is not a viola-
tion of U.S. copyright laws for a consumer to record a broadcast television pro-
gram for private (in-home) viewing.
20
Cassette Deck/VCR Features
You can connect two video sources to the receiver. If you connect a VCR to the
Playing and Recording
Video Tapes
VCR/TAPE 1
DVD/LD
audio and video jacks, you can copy video cassette
and
tapes from one VCR to another and monitor the dubbing process.
Playing a Video Tape
VCR/TAPE 1
To play a video tape, load the tape into the VCR connected to either
DVD/LD
VCR/TAPE 1
DVD/LD
or ) that corresponds to the jack
or
. Press the button (
the VCR is connected to. VCRor DVD/LDappears on the display. Follow the
VCR’s instructions to begin playback. If you connected a monitor to the
TO MONITOR TV
receiver’s
jack, you can view the program on that monitor.
Copying a Video Tape
Follow these steps to copy a video tape from one VCR to another through the
STAV-3770.
DVD/LD
1. Load the tape you want to copy into the VCR connected to
.
2. Load a blank tape (or one you want to record over) into the VCR con-
VCR/TAPE 1
nected to the
jacks.
DVD/LD
3. Press
.
4. Begin recording and playback on the VCRs.
Important: Most material performed in public, such as concerts, plays, and
movies, or distributed on prerecorded video tapes is copyrighted. The unautho-
rized recording or duplication of copyrighted material is a violation of the copy-
right laws of most countries and such duplication may result in fines,
imprisonment, or both. Note, however, that in the United States, it is not a viola-
tion of U.S. copyright laws for a consumer to record a broadcast television pro-
gram for private (in-home) viewing.
20
Using Advanced Sound Options
Your receiver has four special sound options: Dolby Pro Logic Surround, Dolby
3CH Logic, DSP Effect, and Dolby Virtual. These special options enhance the
sound from a connected program source.
Notes:
• To get the full benefit from programs encoded with Dolby Surround
Sound, you need a stereo VCR or DVD/LD player.
• Dolby Surround does not operate correctly if the signal passes through a
graphic equalizer. If you connected an equalizer to the TAPE 2 MONITOR
jacks, do not select TAPE 2 MONITOR when you listen to Dolby Surround
signals.
To turn on Dolby Pro Logic Surround or Dolby 3CH Logic, press PRO LOGIC on
the remote control until PROLOGIC, THEATER1, or THEATER2appears on
the display, then press SURROUND followed by CENTER MODE to select NORMAL,
WIDE, PHANTOM, or 3chLOGIC. See “Sound Mode Adjustments (Remote
Control Only)” on Page 22 for information about each of these options.
For Dolby Virtual, press DOLBY VIRTUAL (VIRTUAL on the remote control) to turn
this feature on or off. To turn on a DSP effect, press DSP MODE until the desired
option (see below) appears on the display.
Dolby Pro Logic Surround
Dolby Pro Logic Surround puts you in the middle of the action. The center- and
rear-channel speakers add incredible realism by directing the sound to the
appropriate speakers, making you feel like you are really there. ProLogicis
the standard.
Dolby 3CH Logic
Dolby 3CH Logic produces a more spacious sound field than is possible with
ordinary stereo playback by sending the rear channel’s sound to the front left
and right speakers. Select 3chLOGICwhen you play a Dolby Surround Sound
program and do not have rear speakers.
Dolby Virtual
Dolby Virtual lets you enjoy programs encoded with Dolby Surround while using
only two front speakers.
DSP Effect
You can choose one of five DSP effects — HALL, JAZZ, DANCE, THEATER1,
or THEATER2. Hall simulates a large concert hall, best suited for classical mu-
sic. Jazz provides the acoustic effects generally heard in jazz clubs. Dance
gives the effect of a discotheque. Both theater modes provide the effect of a
movie theater. THEATER 1 sounds like a large movie theater. THEATER 2
seems like a smaller theater. Try each setting to find the best effect for your pro-
grams.
21
Using Advanced Sound Options
Your receiver has four special sound options: Dolby Pro Logic Surround, Dolby
3CH Logic, DSP Effect, and Dolby Virtual. These special options enhance the
sound from a connected program source.
Notes:
• To get the full benefit from programs encoded with Dolby Surround
Sound, you need a stereo VCR or DVD/LD player.
• Dolby Surround does not operate correctly if the signal passes through a
graphic equalizer. If you connected an equalizer to the TAPE 2 MONITOR
jacks, do not select TAPE 2 MONITOR when you listen to Dolby Surround
signals.
To turn on Dolby Pro Logic Surround or Dolby 3CH Logic, press PRO LOGIC on
the remote control until PROLOGIC, THEATER1, or THEATER2appears on
the display, then press SURROUND followed by CENTER MODE to select NORMAL,
WIDE, PHANTOM, or 3chLOGIC. See “Sound Mode Adjustments (Remote
Control Only)” on Page 22 for information about each of these options.
For Dolby Virtual, press DOLBY VIRTUAL (VIRTUAL on the remote control) to turn
this feature on or off. To turn on a DSP effect, press DSP MODE until the desired
option (see below) appears on the display.
Dolby Pro Logic Surround
Dolby Pro Logic Surround puts you in the middle of the action. The center- and
rear-channel speakers add incredible realism by directing the sound to the
appropriate speakers, making you feel like you are really there. ProLogicis
the standard.
Dolby 3CH Logic
Dolby 3CH Logic produces a more spacious sound field than is possible with
ordinary stereo playback by sending the rear channel’s sound to the front left
and right speakers. Select 3chLOGICwhen you play a Dolby Surround Sound
program and do not have rear speakers.
Dolby Virtual
Dolby Virtual lets you enjoy programs encoded with Dolby Surround while using
only two front speakers.
DSP Effect
You can choose one of five DSP effects — HALL, JAZZ, DANCE, THEATER1,
or THEATER2. Hall simulates a large concert hall, best suited for classical mu-
sic. Jazz provides the acoustic effects generally heard in jazz clubs. Dance
gives the effect of a discotheque. Both theater modes provide the effect of a
movie theater. THEATER 1 sounds like a large movie theater. THEATER 2
seems like a smaller theater. Try each setting to find the best effect for your pro-
grams.
21
Using Advanced Sound Options
Center Mode Setting
Sound Mode Adjustments
(Remote Control Only)
The center mode setting affects the center channel’s bass signals. It operates
only when you select the Dolby Pro Logic Surround or Dolby 3CH Logic mode.
SURROUND
CENTER MODE
. Each time you
On the remote control, press
then
Note: If you do not use a center speaker,
the monaural signals are only repro-
duced if you select PHANTOM.
CENTER MODE
press
, the setting changes: NORMAL, WIDE, PHANTOM, or
3chLOGIC.
NORMAL — For a small center speaker. The front left and right speakers play
the center-channel bass sounds.
WIDE— For a medium or large center speaker. The center speaker plays the
center-channel bass sounds.
PHANTOM— For no center speaker. All center-channel sound comes from the
front left and right speakers.
3chLOGIC— For no rear speakers. The rear channel’s sound is sent to the
front left and right speakers.
Test Tone
The test tone lets you balance the signal levels between all your speakers. To
adjust the levels, see “Center Level” and “Rear Level.”
To turn on the test tone, select one of the surround sound modes (PROLOGIC,
SURROUND
THEATER1, THEATER2, or 3chLOGIC) then press
. Then press
TEST TONE
. The receiver sounds a 2-second tone from the front left, center, front
right, and surround (rear) speakers, in sequence. Lch, Cch, Rch, and Sch
appear as the test tone sounds.
The center test tone sounds and Cchappears only when you select Normal,
Wide, or 3CHLogic.
If you select 3CHLogic, the receiver sounds the 2-second tone from the left,
center, and right speakers, in sequence.
TEST TONE
Press
again to turn off this feature.
Center Level
Note: Use the VOLUME control to adjust
the overall sound level.
– CENTER LEVEL +
Press
to adjust the center speaker sound level.
Rear Level
– REAR LEVEL +
Press
to adjust the rear speakers’ sound level.
22
Using Advanced Sound Options
Center Mode Setting
Sound Mode Adjustments
(Remote Control Only)
The center mode setting affects the center channel’s bass signals. It operates
only when you select the Dolby Pro Logic Surround or Dolby 3CH Logic mode.
SURROUND
CENTER MODE
. Each time you
On the remote control, press
then
Note: If you do not use a center speaker,
the monaural signals are only repro-
duced if you select PHANTOM.
CENTER MODE
press
, the setting changes: NORMAL, WIDE, PHANTOM, or
3chLOGIC.
NORMAL — For a small center speaker. The front left and right speakers play
the center-channel bass sounds.
WIDE— For a medium or large center speaker. The center speaker plays the
center-channel bass sounds.
PHANTOM— For no center speaker. All center-channel sound comes from the
front left and right speakers.
3chLOGIC— For no rear speakers. The rear channel’s sound is sent to the
front left and right speakers.
Test Tone
The test tone lets you balance the signal levels between all your speakers. To
adjust the levels, see “Center Level” and “Rear Level.”
To turn on the test tone, select one of the surround sound modes (PROLOGIC,
SURROUND
THEATER1, THEATER2, or 3chLOGIC) then press
. Then press
TEST TONE
. The receiver sounds a 2-second tone from the front left, center, front
right, and surround (rear) speakers, in sequence. Lch, Cch, Rch, and Sch
appear as the test tone sounds.
The center test tone sounds and Cchappears only when you select Normal,
Wide, or 3CHLogic.
If you select 3CHLogic, the receiver sounds the 2-second tone from the left,
center, and right speakers, in sequence.
TEST TONE
Press
again to turn off this feature.
Center Level
Note: Use the VOLUME control to adjust
the overall sound level.
– CENTER LEVEL +
Press
to adjust the center speaker sound level.
Rear Level
– REAR LEVEL +
Press
to adjust the rear speakers’ sound level.
22
Using Advanced Sound Options
Delay Time
In the Dolby Pro Logic Surround modes (PROLOGIC, THEATER1, and THE-
ATER2), the receiver slightly delays the sound going to the rear speakers. You
can change this delay time from 15 to 30 milliseconds (ms) in 5 ms steps. Adjust
the delay time for the best surround effect.
Notes:
• For Dolby Pro Logic Surround, the de-
lay is preset to 5 ms.
• The delay time does not affect the
DSP or Dolby Virtual mode.
Press SURROUND, then hold down DELAY TIME to change the delay time. The
receiver displays the selected time.
Effect Level
With DSP and Dolby Virtual, you can change the delay time to alter the sound
effect. You can set different levels for each mode independently (from 10 to 90
for DSP, and from 30 to 90 for Dolby Virtual).
Press SURROUND, then hold down DISC EFFECT – or + to change the effect level.
Dolby Virtual effects change considerably when the listening position changes.
It sounds best when you move farther away from the speakers (about 1.2 times
farther than the distance between the left and right speakers).
Also, the effect can vary depending on the source program.
23
Using Advanced Sound Options
Delay Time
In the Dolby Pro Logic Surround modes (PROLOGIC, THEATER1, and THE-
ATER2), the receiver slightly delays the sound going to the rear speakers. You
can change this delay time from 15 to 30 milliseconds (ms) in 5 ms steps. Adjust
the delay time for the best surround effect.
Notes:
• For Dolby Pro Logic Surround, the de-
lay is preset to 5 ms.
• The delay time does not affect the
DSP or Dolby Virtual mode.
Press SURROUND, then hold down DELAY TIME to change the delay time. The
receiver displays the selected time.
Effect Level
With DSP and Dolby Virtual, you can change the delay time to alter the sound
effect. You can set different levels for each mode independently (from 10 to 90
for DSP, and from 30 to 90 for Dolby Virtual).
Press SURROUND, then hold down DISC EFFECT – or + to change the effect level.
Dolby Virtual effects change considerably when the listening position changes.
It sounds best when you move farther away from the speakers (about 1.2 times
farther than the distance between the left and right speakers).
Also, the effect can vary depending on the source program.
23
Using the Remote Control
The remote control works up to a distance of about 23 feet, and within a 30-
degree angle on either side of the receiver. Point the control at the receiver’s
front panel and press the desired button(s).
Many buttons on the remote control work the same as buttons on the receiver’s
front panel. Use these buttons exactly as you would use the corresponding but-
tons on the receiver.
CONTROL MODE Buttons
The three CONTROL MODE buttons select the device you connected to the CON-
TROL OUT jack of the STAV-3770, CD player, VCR, or cassette deck.
Receiver/Amplifier Operation
Before operation, press TUNER to select receiver/amplifier operation.
STATION
BAND
Tunes to the next higher or lower memory location.
Selects the AM or FM tuner band.
Tunes to radio stations.
TUNER
FREQ
Selects the FM reception mode.
Selects the memory class.
FM MONO
CD
POWER
BAND
STATION
FREQ
CLASS
TAPE
TUNER
Allows direct input of the station frequency.
DIRECT ACCESS
Number Buttons
FM
MONO
DIRECT
ACCESS
CLASS
Select the corresponding memory station. During Direct Access,
enter the station’s frequency.
1
2
3
TEST
TONE
REAR
LEVEL
Receiver/
Amplifier
Buttons
SUR-
TEST TONE
Sounds test tones from each speaker when pressed after
ROUND.
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
CONTROL
MODE
7
DISC
EFFECT
DELAY
TIME
SURROUND
– REAR LEVEL +
CENTER MODE
– CENTER LEVEL +
DELAY TIME
Controls the sound level of the rear speakers when pressed after
SURROUND.
0
PRO LOGICDSP MODE MUTING
VIRTUAL
FUNC
LOUD
Selects among the three center modes or 3CH Logic when
pressed after SURROUND.
MASTER
VOLUME
RECEIVER
POWER
DIRECT
AUDIO/VIDEO
SYSTEM REMOTE
OSR
Controls the sound level of the center speaker when pressed af-
ter SURROUND.
Sets the rear-channel delay for Dolby Pro Logic Surround and
Simulated Surround programs when pressed after SURROUND.
– EFFECT+
PRO LOGIC
DSP MODE
Adjusts the level of DSP or Dolby Virtual mode.
Selects Dolby Pro Logic Surround.
RECEIVER POWER
Selects the DSP mode; HALL, JAZZ, DANCE, THEATER 1, or
THEATER 2.
MUTING
Silences the receiver. Press again to restore the sound to its pre-
vious level.
Selects Dolby Virtual.
VIRTUAL
LOUD
Turns the loudness feature on and off.
Selects a program source (VCR, PHONO, tuner, CD, or DVD/
LD). Repeatedly press until the display shows the desired pro-
gram source.
FUNC
24
Using the Remote Control
The remote control works up to a distance of about 23 feet, and within a 30-
degree angle on either side of the receiver. Point the control at the receiver’s
front panel and press the desired button(s).
Many buttons on the remote control work the same as buttons on the receiver’s
front panel. Use these buttons exactly as you would use the corresponding but-
tons on the receiver.
CONTROL MODE Buttons
The three CONTROL MODE buttons select the device you connected to the CON-
TROL OUT jack of the STAV-3770, CD player, VCR, or cassette deck.
Receiver/Amplifier Operation
Before operation, press TUNER to select receiver/amplifier operation.
STATION
BAND
Tunes to the next higher or lower memory location.
Selects the AM or FM tuner band.
Tunes to radio stations.
TUNER
FREQ
Selects the FM reception mode.
Selects the memory class.
FM MONO
CD
POWER
BAND
STATION
FREQ
CLASS
TAPE
TUNER
Allows direct input of the station frequency.
DIRECT ACCESS
Number Buttons
FM
MONO
DIRECT
ACCESS
CLASS
Select the corresponding memory station. During Direct Access,
enter the station’s frequency.
1
2
3
TEST
TONE
REAR
LEVEL
Receiver/
Amplifier
Buttons
SUR-
TEST TONE
Sounds test tones from each speaker when pressed after
ROUND.
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
CONTROL
MODE
7
DISC
EFFECT
DELAY
TIME
SURROUND
– REAR LEVEL +
CENTER MODE
– CENTER LEVEL +
DELAY TIME
Controls the sound level of the rear speakers when pressed after
SURROUND.
0
PRO LOGICDSP MODE MUTING
VIRTUAL
FUNC
LOUD
Selects among the three center modes or 3CH Logic when
pressed after SURROUND.
MASTER
VOLUME
RECEIVER
POWER
DIRECT
AUDIO/VIDEO
SYSTEM REMOTE
OSR
Controls the sound level of the center speaker when pressed af-
ter SURROUND.
Sets the rear-channel delay for Dolby Pro Logic Surround and
Simulated Surround programs when pressed after SURROUND.
– EFFECT+
PRO LOGIC
DSP MODE
Adjusts the level of DSP or Dolby Virtual mode.
Selects Dolby Pro Logic Surround.
RECEIVER POWER
Selects the DSP mode; HALL, JAZZ, DANCE, THEATER 1, or
THEATER 2.
MUTING
Silences the receiver. Press again to restore the sound to its pre-
vious level.
Selects Dolby Virtual.
VIRTUAL
LOUD
Turns the loudness feature on and off.
Selects a program source (VCR, PHONO, tuner, CD, or DVD/
LD). Repeatedly press until the display shows the desired pro-
gram source.
FUNC
24
Using the Remote Control
Bypasses the receiver’s audio control circuits. Press again to re-
store the previous settings.
DIRECT
+ MASTER VOLUME – Adjusts the system’s volume.
Turns the receiver on and off.
RECEIVER POWER
CD
CD Player Operation
Note: You must have connected the CD player to both of your receiver’s CON-
TROL OUT and audio jacks for these functions to work.
CD
POWER
BAND
STATION
FREQ
Before operation, press CD to select CD player operation.
TAPE
TUNER
CD Player
Buttons
Turns the CD player on and off (only for CD players that have the
FM
MONO
DIRECT
ACCESS
POWER
CLASS
CONTROL IN/OUT feature).
1
2
3
|
/
|
Returns to the beginning of the current track or advances to the
next track.
TEST
TONE
REAR
LEVEL
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
CONTROL
MODE
7
DISC
EFFECT
/
Rapidly advances backward/forward within a track.
Press to pause play. Press again to resume.
Stops playback.
DELAY
TIME
SURROUND
0
PRO LOGICDSP MODE MUTING
VIRTUAL
FUNC
LOUD
MASTER
VOLUME
RECEIVER
POWER
DIRECT
Plays the CD.
AUDIO/VIDEO
SYSTEM REMOTE
OSR
– DISC +
Selects discs in a multi-play CD changer. (DISC might not work
with some CD players.)
Cassette Deck Operation
Note: You must have connected the cassette deck to both your receiver’s CON-
TROL OUT and audio jacks for these functions to work.
TAPE
Before operation, press TAPE to select cassette deck operation.
The remote control operates a single cassette deck and Deck 2 on a dual cas-
sette deck. To operate Deck 1 on a dual cassette deck, use the buttons shown
in parentheses.
CD
POWER
BAND
STATION
TAPE
TUNER
FREQ
Note: These buttons do not work with all decks.
Cassette
Deck
Buttons
FM
MONO
DIRECT
ACCESS
CLASS
Turns on/off the cassette deck.
POWER
(7)
1
2
3
TEST
TONE
REAR
LEVEL
Press to play the other side of an auto-reverse cassette deck.
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
(8) /
(9)
Quickly locates and plays the beginning of recorded material dur-
ing play.
CONTROL
MODE
7
DISC
EFFECT
DELAY
TIME
SURROUND
0
PRO LOGICDSP MODE MUTING
Or, when the tape is stopped, rapidly searches forward or back-
ward to locate a specific section of the tape.
VIRTUAL
FUNC
LOUD
MASTER
VOLUME
RECEIVER
POWER
DIRECT
(0)
Press to temporarily stop playback/recording. Press again to re-
sume.
AUDIO/VIDEO
SYSTEM REMOTE
OSR
(EFFECT –)
(+ EFFECT)
Stops playback/recording.
Press to start normal playback.
25
Using the Remote Control
Bypasses the receiver’s audio control circuits. Press again to re-
store the previous settings.
DIRECT
+ MASTER VOLUME – Adjusts the system’s volume.
Turns the receiver on and off.
RECEIVER POWER
CD
CD Player Operation
Note: You must have connected the CD player to both of your receiver’s CON-
TROL OUT and audio jacks for these functions to work.
CD
POWER
BAND
STATION
FREQ
Before operation, press CD to select CD player operation.
TAPE
TUNER
CD Player
Buttons
Turns the CD player on and off (only for CD players that have the
FM
MONO
DIRECT
ACCESS
POWER
CLASS
CONTROL IN/OUT feature).
1
2
3
|
/
|
Returns to the beginning of the current track or advances to the
next track.
TEST
TONE
REAR
LEVEL
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
CONTROL
MODE
7
DISC
EFFECT
/
Rapidly advances backward/forward within a track.
Press to pause play. Press again to resume.
Stops playback.
DELAY
TIME
SURROUND
0
PRO LOGICDSP MODE MUTING
VIRTUAL
FUNC
LOUD
MASTER
VOLUME
RECEIVER
POWER
DIRECT
Plays the CD.
AUDIO/VIDEO
SYSTEM REMOTE
OSR
– DISC +
Selects discs in a multi-play CD changer. (DISC might not work
with some CD players.)
Cassette Deck Operation
Note: You must have connected the cassette deck to both your receiver’s CON-
TROL OUT and audio jacks for these functions to work.
TAPE
Before operation, press TAPE to select cassette deck operation.
The remote control operates a single cassette deck and Deck 2 on a dual cas-
sette deck. To operate Deck 1 on a dual cassette deck, use the buttons shown
in parentheses.
CD
POWER
BAND
STATION
TAPE
TUNER
FREQ
Note: These buttons do not work with all decks.
Cassette
Deck
Buttons
FM
MONO
DIRECT
ACCESS
CLASS
Turns on/off the cassette deck.
POWER
(7)
1
2
3
TEST
TONE
REAR
LEVEL
Press to play the other side of an auto-reverse cassette deck.
4
5
8
6
9
CENTER
MODE
CENTER
LEVEL
(8) /
(9)
Quickly locates and plays the beginning of recorded material dur-
ing play.
CONTROL
MODE
7
DISC
EFFECT
DELAY
TIME
SURROUND
0
PRO LOGICDSP MODE MUTING
Or, when the tape is stopped, rapidly searches forward or back-
ward to locate a specific section of the tape.
VIRTUAL
FUNC
LOUD
MASTER
VOLUME
RECEIVER
POWER
DIRECT
(0)
Press to temporarily stop playback/recording. Press again to re-
sume.
AUDIO/VIDEO
SYSTEM REMOTE
OSR
(EFFECT –)
(+ EFFECT)
Stops playback/recording.
Press to start normal playback.
25
Troubleshooting
If the receiver is not working as it should, the following suggestions might help. If you follow the suggestions in this chart and
the receiver still does not work properly, contact your local RadioShack store for assistance.
Problem
Cause
Suggestion
Plug in the power cord.
Unplug the power cord, then plug it in again.
Power does not turn on.
Power cord is disconnected.
Protection circuit is activated.
The receiver does not respond
to button presses.
Static discharge has affected the re- Unplug the power cord, then plug it in again. (If
ceiver.
static electricity is a problem, use the remote control
as much as possible.)
No sound.
Incorrect connections.
Check and correct the connections.
Press MUTING.
The mute function is activated.
The volume is turned down.
Speaker wires are disconnected.
Speakers are turned off.
Turn up the volume.
Connect the speaker wires.
Press SPEAKER so SP Aappears on the display.
Press TAPE 2 so TAPE2clears from the display.
TAPE 2 function is engaged.
No picture when you select a
video source.
The selected video source is not set Correct the problem with the selected video source.
correctly.
Incorrect connections.
Station not correctly tuned.
Antenna not connected.
Check and correct the connections.
Adjust tuning.
High noise level.
Connect the antenna.
FM antenna still coiled or is not
pointing in the correct direction.
Stretch both ends of the antenna taut and reposition
the antenna.
AM loop antenna not pointing in the Adjust the AM loop antenna.
correct direction.
Noise is coming from another electri- Try using an AC line noise filter to reduce the noise.
cal appliance.
Automatic tuning does not stop Stations are too weak.
when searching for stations.
Use a better antenna.
Cannot make copies of video
tapes.
Tapes are protected by a copy pro-
tection method.
You cannot make a good copy.
Video connections are incorrect.
Remote is set to other device.
Check and correct the connections.
Remote control does not work.
Press the CONTROL MODE button for the device to
control (CD, TAPE, or TUNER).
Batteries are weak.
Replace the batteries.
Remote does not control cas-
sette deck or CD player.
Cassette deck or CD player is not
compatible.
The feature only works with Optimus Professional
Series components.
Control cable is not plugged in.
Audio cables are not plugged in.
Properly connect the control cable.
Properly connect the audio cables.
26
Troubleshooting
If the receiver is not working as it should, the following suggestions might help. If you follow the suggestions in this chart and
the receiver still does not work properly, contact your local RadioShack store for assistance.
Problem
Cause
Suggestion
Plug in the power cord.
Unplug the power cord, then plug it in again.
Power does not turn on.
Power cord is disconnected.
Protection circuit is activated.
The receiver does not respond
to button presses.
Static discharge has affected the re- Unplug the power cord, then plug it in again. (If
ceiver.
static electricity is a problem, use the remote control
as much as possible.)
No sound.
Incorrect connections.
Check and correct the connections.
Press MUTING.
The mute function is activated.
The volume is turned down.
Speaker wires are disconnected.
Speakers are turned off.
Turn up the volume.
Connect the speaker wires.
Press SPEAKER so SP Aappears on the display.
Press TAPE 2 so TAPE2clears from the display.
TAPE 2 function is engaged.
No picture when you select a
video source.
The selected video source is not set Correct the problem with the selected video source.
correctly.
Incorrect connections.
Station not correctly tuned.
Antenna not connected.
Check and correct the connections.
Adjust tuning.
High noise level.
Connect the antenna.
FM antenna still coiled or is not
pointing in the correct direction.
Stretch both ends of the antenna taut and reposition
the antenna.
AM loop antenna not pointing in the Adjust the AM loop antenna.
correct direction.
Noise is coming from another electri- Try using an AC line noise filter to reduce the noise.
cal appliance.
Automatic tuning does not stop Stations are too weak.
when searching for stations.
Use a better antenna.
Cannot make copies of video
tapes.
Tapes are protected by a copy pro-
tection method.
You cannot make a good copy.
Video connections are incorrect.
Remote is set to other device.
Check and correct the connections.
Remote control does not work.
Press the CONTROL MODE button for the device to
control (CD, TAPE, or TUNER).
Batteries are weak.
Replace the batteries.
Remote does not control cas-
sette deck or CD player.
Cassette deck or CD player is not
compatible.
The feature only works with Optimus Professional
Series components.
Control cable is not plugged in.
Audio cables are not plugged in.
Properly connect the control cable.
Properly connect the audio cables.
26
Care and Maintenance
Your Optimus STAV-3770 Audio/Video Receiver is an example of superior design and craftsmanship. The following sugges-
tions will help you care for the receiver so you can enjoy it for years.
Keep the receiver dry. If it gets wet, wipe it dry immediately. Liquids can contain
minerals that can corrode the electronic circuits.
Handle the receiver gently and carefully. Dropping it can damage its circuit
boards and can cause the receiver to work improperly.
Use and store the receiver and its remote control only in normal temperature
environments. Temperature extremes can shorten the life of electronic devices,
damage batteries, and distort or melt plastic parts.
Keep the receiver away from dust and dirt, which can cause premature wear of
parts.
Wipe the receiver with a damp cloth occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or strong detergents to clean the
receiver.
Use only fresh batteries of the recommended size and type in the remote con-
trol. Always remove old or weak batteries. They can leak chemicals that can
destroy electronic circuits.
Modifying or tampering with your receiver’s internal components can cause a malfunction and might invalidate the receiver’s
warranty and void your FCC authorization to operate it. If the receiver is not operating as it should, take it to your local
RadioShack store for assistance.
27
Care and Maintenance
Your Optimus STAV-3770 Audio/Video Receiver is an example of superior design and craftsmanship. The following sugges-
tions will help you care for the receiver so you can enjoy it for years.
Keep the receiver dry. If it gets wet, wipe it dry immediately. Liquids can contain
minerals that can corrode the electronic circuits.
Handle the receiver gently and carefully. Dropping it can damage its circuit
boards and can cause the receiver to work improperly.
Use and store the receiver and its remote control only in normal temperature
environments. Temperature extremes can shorten the life of electronic devices,
damage batteries, and distort or melt plastic parts.
Keep the receiver away from dust and dirt, which can cause premature wear of
parts.
Wipe the receiver with a damp cloth occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or strong detergents to clean the
receiver.
Use only fresh batteries of the recommended size and type in the remote con-
trol. Always remove old or weak batteries. They can leak chemicals that can
destroy electronic circuits.
Modifying or tampering with your receiver’s internal components can cause a malfunction and might invalidate the receiver’s
warranty and void your FCC authorization to operate it. If the receiver is not operating as it should, take it to your local
RadioShack store for assistance.
27
The FCC Wants You to Know
Your receiver might cause radio or TV interference even when it is operating
properly. To determine whether your receiver is causing the interference, turn off
your receiver. If the interference goes away, your receiver is causing it. Try to
eliminate the interference by:
• Moving your radio or TV away from the receiver
• Connecting your receiver to an outlet that is on a different electrical circuit
from the radio or TV
• Contacting your local RadioShack store for help
If you cannot eliminate the interference, the FCC requires that you stop using
your receiver.
28
The FCC Wants You to Know
Your receiver might cause radio or TV interference even when it is operating
properly. To determine whether your receiver is causing the interference, turn off
your receiver. If the interference goes away, your receiver is causing it. Try to
eliminate the interference by:
• Moving your radio or TV away from the receiver
• Connecting your receiver to an outlet that is on a different electrical circuit
from the radio or TV
• Contacting your local RadioShack store for help
If you cannot eliminate the interference, the FCC requires that you stop using
your receiver.
28
Specifications
Amplifier
Front Channel Average Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel into 8 Ohms
From 40 to 20,000 Hz,
With No More than 0.9% Total Harmonic Distortion
Measured Pursuant to the Federal Trade Commission’s
Trade Regulation Rule on Amplifier Output Power Claims
Front Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel (1 kHz, 0.9% THD, 8 Ohms)
Center Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts (1 kHz, 0.9% THD, 8 Ohms)
Continuous Rear Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts (1 kHz, 0.9% THD, 8 Ohms)
Input Sensitivity/Impedance
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/47 kOhms
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kOhms
Phono Overload Level (0.1% THD, 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mV
Frequency Response
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz to 20,000 Hz ±0.3 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 100,000 Hz +0/–3 dB
Output Level/Impedance
VCR/TAPE 1 REC, TAPE 2 Monitor REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kOhms
Tone Controls
Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (150 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (10 kHz)
Loudness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8 dB/+6 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio (IHF, Short Circuited, A Network)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 dB
Signal-to-Noise Ratio (EIA, at 1 Watt, 1 kHz)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 dB
Video Section
Input Sensitivity/Impedance VCR/TAPE 1, DVD/LD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Output Level/Impedance VCR/TAPE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Frequency Response VCR/TAPE 1, DVD/LD to Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 7 MHz +0/–3 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
29
Specifications
Amplifier
Front Channel Average Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel into 8 Ohms
From 40 to 20,000 Hz,
With No More than 0.9% Total Harmonic Distortion
Measured Pursuant to the Federal Trade Commission’s
Trade Regulation Rule on Amplifier Output Power Claims
Front Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel (1 kHz, 0.9% THD, 8 Ohms)
Center Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts (1 kHz, 0.9% THD, 8 Ohms)
Continuous Rear Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts (1 kHz, 0.9% THD, 8 Ohms)
Input Sensitivity/Impedance
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/47 kOhms
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kOhms
Phono Overload Level (0.1% THD, 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mV
Frequency Response
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz to 20,000 Hz ±0.3 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 100,000 Hz +0/–3 dB
Output Level/Impedance
VCR/TAPE 1 REC, TAPE 2 Monitor REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kOhms
Tone Controls
Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (150 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (10 kHz)
Loudness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8 dB/+6 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio (IHF, Short Circuited, A Network)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 dB
Signal-to-Noise Ratio (EIA, at 1 Watt, 1 kHz)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 dB
CD, DVD/LD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 dB
Video Section
Input Sensitivity/Impedance VCR/TAPE 1, DVD/LD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Output Level/Impedance VCR/TAPE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Frequency Response VCR/TAPE 1, DVD/LD to Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 7 MHz +0/–3 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
29
Specifications
FM Tuner
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 108 MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono: 13.2 dBf, IHF (1.3 µV/75 Ohms)
50 dB Quieting Sensitivity
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.2 dBf
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.6 dBf
Signal-to-Noise Ratio
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 dB (at 85 dBf)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB (at 85 dBf)
Distortion Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB (400 kHz)
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Hz to 15 kHz (±1 dB)
Antenna Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Ohms Unbalanced
AM Tuner
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1700 kHz
Sensitivity (IHF, Loop Antenna) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
General
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Volts AC, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Watts, 300 VA (UL)
AC Outlet Ratings Switched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total 100 Watts (0.8 Amps) Maximum
Dimensions (HWD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55/8 × 169/16 × 1213/16 Inches
(143 × 420 × 325 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 lb 5 oz
(7.4 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
30
Specifications
FM Tuner
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 108 MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono: 13.2 dBf, IHF (1.3 µV/75 Ohms)
50 dB Quieting Sensitivity
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.2 dBf
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.6 dBf
Signal-to-Noise Ratio
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 dB (at 85 dBf)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB (at 85 dBf)
Distortion Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB (400 kHz)
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Hz to 15 kHz (±1 dB)
Antenna Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Ohms Unbalanced
AM Tuner
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1700 kHz
Sensitivity (IHF, Loop Antenna) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
General
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Volts AC, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Watts, 300 VA (UL)
AC Outlet Ratings Switched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total 100 Watts (0.8 Amps) Maximum
Dimensions (HWD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55/8 × 169/16 × 1213/16 Inches
(143 × 420 × 325 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 lb 5 oz
(7.4 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
30
Index to Features by Control Name
This table lists the control and indicator names found on the front of your receiver, along with the page number where the con-
trol or indicator is discussed. To find a description for the buttons on the remote control, see “Using the Remote Control” on
Page 24.
Control
Page
15, 17
TONE/BALANCE
BASS
15
CD
15
CLASS
17
DOLBY PRO LOGIC
DOLBY VIRTUAL
DSP MODE
DVD/LD
21
21, 23
21
15
FM MONO
FM/AM
17
16
LOUDNESS
MEMORY
18
17
PHONES
18
PHONO
15
POWER
15
SELECT
15, 16
15, 18
17
SPEAKER
STATION
TAPE 2 MONITOR
15, 19
15
TREBLE
TUNING
16
VCR/TAPE 1
15, 19
15
VOLUME
31
Index to Features by Control Name
This table lists the control and indicator names found on the front of your receiver, along with the page number where the con-
trol or indicator is discussed. To find a description for the buttons on the remote control, see “Using the Remote Control” on
Page 24.
Control
Page
15, 17
TONE/BALANCE
BASS
15
CD
15
CLASS
17
DOLBY PRO LOGIC
DOLBY VIRTUAL
DSP MODE
DVD/LD
21
21, 23
21
15
FM MONO
FM/AM
17
16
LOUDNESS
MEMORY
18
17
PHONES
18
PHONO
15
POWER
15
SELECT
15, 16
15, 18
17
SPEAKER
STATION
TAPE 2 MONITOR
15, 19
15
TREBLE
TUNING
16
VCR/TAPE 1
15, 19
15
VOLUME
31
Limited Two-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for two (2) years from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
<ARB7149-A>
6A8
Printed in Indonesia
Limited Two-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for two (2) years from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
<ARB7149-A>
6A8
Printed in Indonesia
|