Miele Clothes Dryer 4580690 User Manual

NOVOT ONIC  
Operating instructions  
for condenser tumble dryer  
T 440 C  
It is essential to read these opera-  
ting instructions before installing or  
using the machine to avoid the risk  
of accident, or damage to the  
machine.  
Q
T.-Nr. 4580690  
 
Guide to the appliance  
1 a.c. connection cable (2 m long)  
with plug for connection to  
240 V 50 Hz, 13 A (GB)  
2 Condensed water container  
3 Drum door  
4 Control panel  
5 Drain hose for condensed water  
6 Four height-adjustable screw feet  
3
 
Guide to the appliance  
Pushbuttons  
Programme selector switch  
Door  
Cottons  
opens the door  
Extra dry  
On/Off  
Normal+  
for switching the appliance on and off.  
Normal  
Hand iron r  
Hand iron rr  
Machine iron  
Low temperature  
low temperatures for delicate fabrics,  
e.g. acrylics.  
Minimum iron  
Buzzer  
sounds when the drum turns during the  
intermittent anti-crease action period.  
Normal+  
Normal  
Hand iron  
Start  
starts a drying programme  
Timed drying  
Indicator light “Empty out container”  
15 mins cool air  
20 mins warm air  
Programme sequence indicator lights  
Drying stage display  
On  
This shows the stage of drying  
Drying  
reached. For programmes “Normal +”  
and “Extra dry” the indicator light re-  
mains at the “Normal” position.  
Cooling down  
Anti-crease/Finish  
4
 
Guide to the appliance  
Environmentally conscious drying  
Energy saving tips  
The sensitive system automatically ad-  
justs drying to suit the water quality.  
The water conductivity is measured,  
and registered by the control which  
Make sure that your laundry is thor-  
oughly spun before drying. You will  
save up to 35% energy and time if  
laundry is spun at full spin speed in-  
then compensates to achieve a uniform stead of at 600 rpm. Load according to  
residual moisture level. The Novotronic  
control offers 9 programmes with elec-  
tronic moisture measuring and 2 timed  
programmes. The automatic reversing  
action turns the drum clockwise and  
anti-clockwise to loosen the laundry  
and prevent damp patches and thus to  
ensure even drying results.  
the optimum amount of washing for the  
programme to be selected. Underload-  
ing is uneconomical. Overloading gives  
a poorer quality of drying and may  
cause unnecessary creasing.  
Before using for the first time  
Important: The appliance must be  
properly installed and connected to  
the electricity supply.  
Warning and safety instructions  
liable for damage resulting from im-  
proper use or operation.  
Please read the operating instruc-  
tions before using the tumble dryer  
for the first time. They contain im-  
portant information about the safety,  
use and maintenance of the ma-  
chine. This will avoid the risk of acci-  
dents and damage to the machine.  
Keep these operating instructions in  
a safe place and ensure that new  
users are familiar with the content.  
Pass them on any future owner of  
the machine.  
Do not let small children play with  
the machine and its controls or  
operate it. Please supervise its use by  
the elderly or infirm.  
Technical safety  
Before connecting the machine, en-  
sure that the connection data on  
the data plate (fusing, voltage and fre-  
quency) matches the mains electricity  
supply. If in any doubt, consult a quali-  
fied electrician.  
Correct usage  
The tumble dryer is only intended  
for drying fabrics, which have  
been washed in a water solution,  
marked on the manufacturer’s wash  
care label as being suitable for tumble  
drying. Any other applications may be  
dangerous. The manufacturer is not  
Faulty components must only be  
exchanged for Miele original spare  
parts. Only when these parts are fitted  
can the safety standards of the ma-  
chine be guaranteed.  
5
 
Warning and safety instructions  
The electrical safety of this ma-  
chine can only be guaranteed  
Always close the door after use.  
This way you will avoid the danger  
of anyone sitting or leaning on the door,  
which can cause the machine to tip up.  
when continuity is complete between  
the appliance and an effective earthing  
system which complies with local and  
national regulations. It is most import-  
ant that this basic safety requirement is  
regularly tested by a qualified electri-  
cian. The manufacturer can not be held  
responsible for the consequences of an  
inadequate earthing system.  
Do not install the machine in a room  
where the temperature may drop  
below freezing. At very cold tempera-  
tures the machine may be difficult to  
start. At very cold temperatures the ma-  
chine may be difficult to start. Laundry  
will not dry and the “anti-crease” indica-  
The machine is built in accordance tor light will flash to indicate there is a  
with current safety requirements.  
Unauthorised repairs could result in un-  
foreseen dangers for the user, for  
which the manufacturer can not accept  
responsibility. Repairs should only be  
undertaken by a Miele approved engin-  
eer.  
problem. Freezing condensed water in  
the pump, hoses and in the condensed  
water container can lead to damage.  
Make sure the drain hose is se-  
curely attached if you hang it in a  
sink or basin (external drainage of con-  
densed water) to avoid the hose slip-  
ping and the water causing damage.  
In the event of a fault or for clean-  
ing purposes, the machine is only  
completely isolated from the electricity  
supply either when:  
Condensed water is not drinking  
water. It can cause health prob-  
lems in people and animals.  
– the plug is withdrawn, or:  
– it is switched off at the mains  
– the mains fuse is withdrawn.  
Using accessories  
Accessory parts may only be fitted  
when expressly approved by  
Miele. If other parts are used, guaran-  
tee, performance and product liability  
claims may be invalidated.  
Use  
There is a danger of fire with fab-  
rics, which:  
– contain rubber, foam rubber or rub-  
ber-like materials  
– have been treated with inflammable  
Disposal of your old machine  
Before discarding an old machine  
unplug it. Render the plug useless.  
Cut off the cable directly behind the ap-  
pliance to prevent misuse.  
cleaning agents  
– have been splashed with hair lac-  
quer, hair spray, nail varnish remover  
or similar.  
6
 
Notes on laundry care  
Before drying, check the drying symbol  
on the textile care label.  
Note  
Some woven and loopknit materials  
tend to shrink to varying extents de-  
pending on their quality. This tendency  
is exaggerated by over-drying.  
Significance of symbols:  
q = Dry at normal temperature  
r= Dry at low temperature  
s= Do not tumble dry  
When purchasing woven materials, it is  
advisable to take their shrinkage  
properties into account.  
If no symbol is featured dry at your own  
risk applying the following principles:  
Starched washing can also be dried in  
the tumble dryer. In order to achieve  
the usual finish, double the amount of  
starch should be used.  
– Cottons and minimum iron items  
should be dried at a normal tempera-  
ture at the appropriate programme  
setting.  
Select the most suitable programme for  
hand or machine ironing.  
– For delicate fabrics, e.g. acrylic  
fibres, the low temperature setting  
should be selected.  
Minimum iron items should be spun for  
10 to 30 seconds before being tumble  
dried. Such fabrics tend to crease if  
overdried. These items should be given  
only a short period in the dryer, and  
taken out slightly damp. The “Minimum  
iron Normal” programme is recom-  
mended.  
The following fabrics should not be  
dried in a tumble dryer:  
– Woollens and wool blends  
These fabrics tend to become matted  
and shrink.  
– Items filled with down  
The fine fabric interior tends to shrink,  
depending on the quality involved.  
Minimum iron shirts in 100 % cotton  
may crease during tumble drying de-  
pending on the quality and weave.  
– Pure linen  
Minimum iron fabrics tend to crease  
more, the greater the load. This is par-  
ticularly true of very delicate fabrics.  
The load should be reduced to 1.5 kg  
or, if necessary, to 1 kg. The “Hand  
iron” setting is recommended for these  
types of garment. In extreme cases do  
not tumble dry these garments.  
These items should only be machine-  
dried if specified as suitable by the  
manufacturer on the textile care label,  
as the surface of the fabric may other-  
wise tend to “roughen”.  
Dark-coloured garments should be  
dried separately from light-coloured  
garments.  
7
 
Loading the machine  
Unloading the machine  
Load the laundry very loosely into the  
drum.  
At the end of the programme remove  
the washing from the machine. If this is  
not done, the machine automatically  
proceeds into an intermittent anti-  
crease action for 60 minutes. This en-  
tails the drum being rotated at short in-  
tervals in order to reduce the possibility  
of the formation of creases.  
Duvet covers and pillowcases should  
be fastened before drying in order to  
prevent small items from being rolled in-  
side them.  
Once the laundry has been removed,  
check that the drum is empty. Any  
items left in the drum could be dam-  
aged through overdrying in the next  
programme.  
Clean the fluff filter after each drying  
cycle to prevent excessive energy con-  
sumption and longer programme run-  
ning times.  
The door should always be closed after  
use.  
Important: Please check that items  
of laundry cannot be trapped by the  
door as this will cause damage to  
the fabric.  
8
 
Programme selection  
Selecting a programme  
After drying:  
This tumble dryer is fitted with an elec-  
tronic sensor system. The required de-  
gree of dryness is measured and moni-  
tored electronically so that the heating  
element is switched off as soon as it is  
reached. The drying cycle automati-  
cally finishes with a cooling down  
period. This may be followed by the  
anti-crease action cycle.  
Turn the programme selector switch  
to “Finish”.  
Switch the machine off.  
Clean the fluff filter.  
Opening the door during a pro-  
gramme  
If the door is opened during a pro-  
gramme the programme will have to be  
started again:  
The following drying programmes are  
available:  
Close the door.  
Press “Start”.  
The selected programme restarts.  
Cottons  
six drying levels from “Extra dry” to  
“Machine iron”  
The programme is not continued if:  
- There is a power failure lasting more  
than 30 minutes.  
Minimum iron  
three drying levels from “Normal+” to  
“Hand iron”  
- The programme has already reached  
the “Cooling down” or “Anti-crease”  
stage.  
Timed drying  
To reselect a different programme  
during drying:  
15 mins cool air and 20 mins warm air  
Set the programme selector switch  
to the required programme.  
The new programme starts from the be-  
ginning.  
Low temperature  
By selecting “Low temperature” the  
temperature can be lowered for deli-  
cate fabrics (e.g. acrylic).  
To cancel a programme  
Correct procedure:  
Turn the programme selector switch  
to “Finish”.  
Load the drum  
Close the door  
Switch on the machine  
Select a programme by turning the  
selector switch clockwise or anti-  
clockwise.  
Select “Low temperature” if required.  
Press “Start”.  
9
 
Programmes - Cottons  
Extra dry  
Hand iron rr  
Multi-layer fabrics which would not be  
thoroughly dried using the “Normal +”  
programme.  
Cotton or linen fabrics, e.g. table linen,  
bedding, starched laundry, etc.  
max. 5 kg  
max. 5 kg  
Note:  
Note:  
If fabrics are too damp for hand-iron-  
ing, please select the “Hand iron r” pro-  
gramme.  
Jerseywear tends to shrink depending  
on the quality and type of manufactur-  
ing involved. The “Extra dry” pro-  
gramme should therefore not be se-  
lected for these fabrics.  
Machine iron  
Cotton or linen fabrics, including star-  
ched laundry, for machine-ironing.  
Normal+  
max. 5 kg  
Mixed load of cotton fabrics, e.g. towell-  
ing and jerseywear, i.e. single-layer  
and multi-layer fabrics.  
Note:  
The laundry should be rolled up to pre-  
vent it from drying out until it can be  
ironed.  
max. 5 kg  
Normal  
Homogeneous loads of cotton fabrics  
(jerseywear, flannelette sheets, towel-  
ling).  
max. 5 kg  
Note:  
Should certain items still be slightly  
damp, select the “Normal + pro-  
gramme”.  
10  
 
Programmes - Minimum iron and timed drying  
Normal +  
15 minutes cool air  
Minimum iron items made of synthetics  
or blended fabrics, e.g. pullovers,  
dresses, trousers, etc., which are not  
dried adequately in the “Normal” pro-  
gramme.  
Items which are only to be aired.  
max. 5 kg  
20 minutes warm air  
Individual items, e.g. bathing towels,  
bathing trunks.  
max. 2,5 kg  
Normal  
Minimum iron shirts, table cloths, etc.,  
made of blended woven or knitted fab-  
rics, e.g. cotton/synthetics.  
max. 2,5 kg  
Hand iron  
Minimum iron shirts, table cloths, etc.  
made of blended woven or knitted fab-  
rics, e.g. cotton/synthetics, which are  
still to be hand-ironed.  
max. 2,5 kg  
Note for all three programmes:  
With blended fabrics consisting of wool  
and synthetics, consult the manufac-  
turer’s instructions, as the wool compo-  
nent may become matted.  
11  
 
Programmes - Consumption data  
Capacity Final spin speed Electricity  
Drying time incl.  
cooling down  
time  
in a domestic  
washing machine  
(rpm)  
consumption  
(kg)  
5
(kWh)  
(mins)  
Cottons  
Extra dry  
1200  
1400  
1550  
3.44  
3.28  
3.17  
87  
83  
81  
Normal +  
5
5
5
5
1200  
1400  
1550  
3.17  
3.02  
2.91  
81  
77  
75  
Normal  
1200  
1400  
1550  
2.88  
2.74  
2.64  
74  
71  
69  
Hand iron rr  
Machine iron  
1200  
1400  
1550  
2.10  
1.96  
1.86  
56  
53  
51  
1200  
1400  
1550  
1.65  
1.51  
1.41  
47  
43  
41  
Minimum iron  
Normal +  
Normal  
2.5  
2.5  
2.5  
1000  
1000  
1000  
1.68  
1.41  
1.21  
50  
45  
37  
Hand iron  
All consumption data have been obtained through standard tests (EN 61121/A11).  
Different types of fabric, the load and residual moisture after spinning may affect  
the figures given.  
12  
 
Emptying the condensed water container  
During the programme, water is con-  
When the container is empty, release  
the cap. The spout closes automati-  
cally.  
densed and collected in a container on  
the left behind the fascia panel. The  
container holds approx. 4 litres and  
should be emptied after each drying  
programme.  
Push in the container until it clicks  
into place.  
Should the container be inadvertently  
full when the tumble dryer is started or  
if it becomes full during operation:  
The “Empty out container” indicator  
light comes on  
Note:  
The water collected in the container  
has been distilled by evaporation and  
can be used in a steam iron or humidi-  
fier, for example.  
The following points should be remem-  
bered:  
The laundry should be thoroughly  
rinsed before it is loaded in the tumble  
dryer.  
Pull out the container  
As a precautionary measure, the water  
should be passed through a fine sieve  
or coffee filter in order to strain out any  
very small particles of fluff from the  
water which might otherwise cause  
damage.  
Pull forward the cap of the spout as  
indicated by the arrow and hold  
open while emptying the container.  
13  
 
Cleaning and care  
The fluff which occurs during drying is  
collected in the fluff filter in the door.  
Clean the filter after every programme  
to save time and energy.  
Remove fluff from the filters in the  
door opening. These filters can be  
taken out and rinsed if necessary.  
Dry the filters before putting them  
back in place.  
Grip the filter by the recessed  
handle and pull upwards to clean.  
Remove any remaining fluff from the  
hollow part of the door through the  
wide slit at the bottom.  
Before cleaning the tumble dryer: Al-  
ways disconnect the machine from  
the power supply.  
The dryer can be cleaned with a  
cloth using soapy water or a mild  
detergent (not scouring powder) and  
dried with a soft cloth.  
The drum may be cleaned using a  
suitable proprietary stainless steel  
cleaner following the manufactu-  
rer’s instructions.  
The machine must never be hosed  
down. Do not use any abrasive sub-  
stances or scouring pads to  
clean the machine.  
14  
 
Cleaning and care  
Heat exchanger  
The heat exchanger should be cleaned  
once or twice a year.  
Before cleaning, disconnect the ma-  
chine from the mains supply.  
Remove the flap  
Open the door  
Turn both levers on the heat ex-  
changer so that they are vertical  
Turn the flap lever so that it is vertical  
15  
 
Cleaning and care  
Pull out the heat exchanger  
– and along the two long sides  
Stand the heat exchanger  
lengthwise on a towel until it is quite  
dry  
Replace the heat exchanger in the  
reverse order.  
Attempt to pull forward the heat ex-  
changer and the flap to check that both  
are firmly positioned, as otherwise  
water may leak from the machine.  
Clean the heat exchanger:  
– at both ends (front and back)  
16  
 
Problem solving guide  
Drying times are too long.  
Electrical appliances should only be  
repaired by qualified personnel. In-  
correctly repaired machines may  
pose a considerable risk to the  
user.  
Clean the fluff filter in the door.  
The laundry was not spun for a suffi-  
ciently long time.  
The grille under the drum door is  
blocked, preventing any intake of cool  
air.  
There are, however, minor faults which  
can be corrected without contacting  
the Service Department.  
Ventilation is inadequate (e.g. in a small  
room).  
The tumble dryer fails to start when  
switched on.  
When the machine is in operation,  
open a door or the window.  
After cleaning the heat exchanger,  
water leaks from the machine  
Check whether the “On” indicator lamp  
lights up. If so, failure to start may be  
due to an incorrect selection procedure  
sequence when switching on the ma-  
chine.  
- Check that the heat exchanger flap  
has ben replaced correctly. If necess-  
ary, remove and replace.  
Repeat the switch-on procedure in  
the correct sequence (see P. 9).  
Items made of synthetic fibres are  
charged with static electricity after  
drying.  
If the “On” indicator lamp does not light  
up, check that  
Static charge can be reduced by ad-  
ding fabric conditioner during the final  
rinse cycle in the washing machine, or  
a fabric conditioner sheet in the tumble  
dryer.  
the “On/Off” button is depressed  
the door is properly closed  
the mains plug is plugged in and the  
fuse or circuit breaker has not  
tripped.  
Formation of fluff  
Laundry is not sufficiently dry.  
Fluff is principally the result of friction  
when items are worn and washed. Ma-  
chine-drying hardly causes any fluff to  
form and, as has been established by  
research institutes, has no effect on the  
lifetime of fabrics.  
The load consists of dissimilar items in  
terms of size and fabric.  
Select a longer drying programme  
next time.  
Small loads or individual items may  
cause the programme to terminate pre-  
maturely.  
Small loads should therefore be  
“time-dried”.  
17  
 
Problem solving guide  
To open the door in the event of  
power failure  
The “Anti-crease” indicator lamp in  
the sequence indicator display starts  
flashing.  
Release the “On/Off” button and  
then press it in again.  
Press the“Start” button.  
If the indicator lamp starts flashing  
again, this indicates a fault in the ma-  
chine. Please then contact your Miele  
Dealer or the Miele Service Dept.  
The drum door opens during the  
drying cycle.  
The machine has overheated. The tem-  
perature limiter opens the drum door  
and thus causes the machine to switch  
off automatically.  
Using the spatula provided lever the  
door open.  
Possible reasons for overheating:  
The fluff filters in the door and in the  
door opening are clogged.  
The heat exchanger is blocked.  
Before restarting the programme, pro-  
ceed as follows:  
Water droplets appear at the upper  
edge of the drum aperture.  
A double filter system with double seal  
prevents fluff from being deposited in  
the heat exchanger.  
Clean the affected part of the ma-  
chine.  
Press the “Start” button.  
This means that the heat exchanger  
does not need to be cleaned so often.  
Should the drum door open again, this  
must be due to a technical fault and  
the Service Dept. should be contacted.  
The double seal may lead to the build-  
up of condensate. Laundry being  
removed from the machine may come  
into contact with these water droplets.  
They will, however, dry off in a matter of  
minutes.  
18  
 
Problem solving guide  
After-sales service  
In the event of any faults which cannot  
be remedied, or if the appliance is  
under guarantee, please contact:  
The interior drum lighting fails to  
function.  
The bulb may be defective.  
Replace it as follows:  
– your Miele Dealer or  
Switch off the machine or disconnect – the nearest Miele Service Depart-  
from the mains supply.  
ment (see back cover for the ad-  
dress).  
Open the door.  
When contacting the Service Depart-  
ment, please quote the Model and Ser-  
ial nos. of your appliance, both of  
which are shown on the data plate on  
the right hand side below the opening  
to the drum.  
Example:  
Use a 19 mm spanner to unscrew  
the plastic cover inside the drum  
above the door.  
The light bulb must not exceed the  
maximum wattage quoted on the  
data plate and the plastic light cover.  
Replace the bulb and the plastic  
cover.  
The cover must be fixed securely, as  
otherwise moisture may seep in and  
cause a short-circuit.  
The temperature-resistant bulb should  
only be ordered from your Miele Dealer  
or the Service Dept.  
19  
 
Installation  
Important  
The grille below the drum door should  
never be blocked, as this will prevent a  
sufficient intake of cold air.  
Installation  
It is possible to install this appliance  
under a continuous worktop / in a row  
of kitchen units using a special conver-  
sion kit*. The machine lid is replaced  
by a coverplate which must be fitted by  
a suitably competent person to ensure  
electrical safety.  
When installing under a worktop with a  
working height of 900/910 mm: a  
spacer kit * is needed.  
The machine must be perfectly level to  
ensure safe and proper operation.  
Minor differences do not, however,  
have an adverse effect on operation.  
When built under, the programme run-  
ning times may be longer.  
The tumble dryer can also be com-  
bined with a Miele washing machine in  
a washer-dryer stack. For this purpose  
the appropriate stacking kit * to match  
your washing machine is required.  
The screw feet can be adjusted to  
compensate for any uneveness in  
the floor surface.  
* These items are all available from  
your Miele Dealer.  
20  
 
Electrical connection  
For U.K. only:  
ceed as follows:  
This tumble dryer is supplied ready for  
connection to an a.c. single phase 230 V,  
50 Hz supply. The rated load is 3 kW.  
The machine is supplied with a 2 m long  
mains cable with moulded plug and the  
fuse rating is 13 A. The appliance should  
The wire which is coloured green and  
yellow must be connected to the termi-  
nal in the plug which is marked with the  
letter E or by the earth symbol z or  
coloured green or green and yellow.  
The wire which is coloured blue must be  
be connected up only by a qualified elec- connected to the terminal which is marked  
trician, in accordance with national and  
local safety regulations.  
with the letter N or coloured black. The  
wire which is coloured brown must be  
connected to the terminal which is  
marked with the letter L or coloured red.  
For other countries:  
This tumble dryer is supplied ready for  
connection to an a.c. single phase 220 V,  
60 Hz supply. The rated load is 2.86 kW.  
The machine is supplied with a 2 m long  
mains cable with moulded plug and the  
fuse rating is 16 A. The appliance should  
be connected up only by a qualified elec-  
trician, in accordance with national and  
local safety regulations.  
WARNING  
THIS APPLIANCE MUST BE EARTHED.  
Non-rewireable plugs BS 1363 (U.K.)  
If this machine or appliance is fitted  
with a non-rewireable plug, the follow-  
ing information applies:  
If the socket outlets are not suitable for the  
plug supplied with this product, it must be  
cut off and an appropriate plug fitted. The  
plug cut from the flexible cord should be  
disposed of and on no account be in-  
serted into a 13 A socket elsewhere in the  
house (electric shock hazard). The fuse  
cover must be refitted when changing the  
fuse, and if the fuse cover is lost, the plug  
must not be used until a suitable replace-  
ment is obtained. The colour of the correct  
replacement cover is that of the coloured  
insert in the base of the plug, or the colour  
that is embossed in words in the base of  
the plug (as applicable to the design of  
plug fitted). The correct fuse rating of the  
replacement fuses that are ASTA ap-  
proved to BS 1362 should be fitted. Re-  
placement fuse covers may be purchased  
from your local electrical suppliers, elec-  
tricity showroom, or Miele Service  
Agent.  
Connection should be made via a  
fused plug and a suitable switched  
socket which is easily accessible.  
For extra safety it is advisable to install  
a residual current device (RCD) with a  
trip current of 30 mA.  
The voltage, rated load and fuse rating  
are given on the data plate. Please en-  
sure that these match the household  
mains supply.  
Important  
The wires in the mains lead are coloured  
in accordance with the following code:  
Green/yellow = earth  
Blue = neutral  
Brown = live  
As the colours of the wires in the mains  
lead of this appliance may not corre-  
spond with the coloured markings ident-  
ifying the terminals in your plug, pro-  
21  
 
External drainage of condensed water  
The condensed water can be drained  
off directly if the machine is installed  
near a sink, drain outlet, etc.  
Push the drain hose onto the drain  
outlet. Make sure that the hose is  
firmly secured by the clip and not  
kinked.  
Accessories supplied:  
- 2 m drain hose  
- Hose clamp  
- Rubber connection sleeve  
- Hose clip  
Installation:  
Max. drain hose length: 3.0 m  
Max. delivery head: 1.0 m  
Detach the hose clip from the drain  
outlet at the back of the machine  
and remove the rubber plug.  
22  
 
External drainage of condensed water  
The machine is fitted with a non-return  
Connection to wash basin drain outlet  
valve as standard to prevent water from  
flowing back into the machine (eg. if  
the machine is connected to a siphon).  
Push the hose clip (1) and knurled  
nut connector (2) (from the sink drain  
outlet) over the drain hose.  
Put the adapter sleeve (3) supplied  
into the hose.  
Screw the drain hose to the drain out-  
let with the knurled nut connector.  
Close the water inlet port above the  
condensed water container with the  
bottom part of the rubber plug. The  
plug must face towards the interior  
of the machine so that the con-  
densed water container can easily  
be inserted.  
Tighten the hose clip (1) up close to  
the nut (2).  
23  
 
Technical data  
Height. . . . . . . . . . . . . . . . . . . . . . . . . .  
Width . . . . . . . . . . . . . . . . . . . . . . . . . .  
Depth (incl. distance from wall) . . . . . .  
Weight . . . . . . . . . . . . . . . . . . . . . . . . .  
Drum volume . . . . . . . . . . . . . . . . . . . .  
Capacity. . . . . . . . . . . . . . . . . . . . . . . .  
85.0 cm (adjustable +1/-0.5 cm)  
59.5 cm  
60.0 cm  
55 kg  
103 l  
5 kg dry weight  
Voltage . . . . . . . . . . . . . . . . . . . . . . . . .  
Rated load . . . . . . . . . . . . . . . . . . . . . .  
Fuse rating . . . . . . . . . . . . . . . . . . . . . .  
See data plate  
}
Max. delivery head. . . . . . . . . . . . . . . .  
Max. drain hose length. . . . . . . . . . . . .  
1.0 m  
3.0 m  
Test certificates awarded. . . . . . . . . . .  
Electrically suppressed . . . . . . . . . . . .  
Radio/ TV suppression; VDE  
Acc. to DIN EN 60555/VDE 0838  
24  
 
25  
 
26  
 
27  
 
Alteration rights reserved / 000  
GB - 5095  
 

Moxa Technologies Network Card C168H User Manual
Multiquip Appliance Trim Kit MVH 402GHB User Manual
NEC Laptop VT 300 Series User Manual
NEC Projector NP UM352W User Manual
Nintendo Video Games 45496740801 User Manual
NordicTrack Treadmill NTTL24080 User Manual
Numark Industries CD Player CDN 22S User Manual
Panasonic Camcorder AG AC90P User Manual
Panasonic Network Card 2SA1738 User Manual
Panasonic Webcam EB Series User Manual