Panasonic Switch 2SA1022 User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SA1022  
Silicon PNP epitaxial planar type  
For high-frequency amplification  
Complementary to 2SC2295  
Unit: mm  
+0.10  
–0.05  
0.40  
+0.10  
–0.06  
0.16  
3
Features  
High frequency voltage fT  
Mini type package, allowing downsizing of the equipment and  
automatic insertion through the tape packing and the magazine  
packing  
1
2
(0.95) (0.95)  
1.9 0.1  
+0.20  
2.90  
–0.05  
10˚  
Absolute Maximum Ratings Ta = 25°C  
Parameter  
Symbol  
Rating  
30  
Unit  
V
1: Base  
2: Emitter  
3: Collector  
Collector-base voltage (Emitter open) VCBO  
Collector-emitter voltage (Base open) VCEO  
Emitter-base voltage (Collector open) VEBO  
20  
V
EIAJ: SC-59  
Mini3-G1 Package  
5  
V
Collector current  
IC  
PC  
Tj  
30  
mA  
mW  
°C  
°C  
Marking Symbol: E  
Collector power dissipation  
Junction temperature  
Storage temperature  
200  
150  
Tstg  
55 to +150  
Electrical Characteristics Ta = 25°C 3°C  
Parameter  
Base-emitter voltage  
Symbol  
VBE  
Conditions  
VCE = −10 V, IC = −1 mA  
VCB = −10 V, IE = 0  
Min  
Typ  
Max  
Unit  
V
0.7  
Collector-base cutoff current (Emitter open)  
Collector-emitter cutoff current (Base open)  
Emitter-base cutoff current (Collector open)  
Forward current transfer ratio *  
Collector-emitter saturation voltage  
Transition frequency  
ICBO  
ICEO  
0.1  
100  
10  
µA  
µA  
µA  
VCE = −20 V, IB = 0  
IEBO  
VEB = −5 V, IC = 0  
hFE  
VCE = −10 V, IC = −1 mA  
70  
220  
VCE(sat) IC = −10 mA, IB = −1 mA  
0.1  
300  
2.8  
V
fT  
VCB = −10 V, IE = 1 mA, f = 200 MHz  
150  
MHz  
dB  
Noise figure  
NF  
Zrb  
Cre  
VCB = −10 V, IE = 1 mA, f = 5 MHz  
VCB = −10 V, IE = 1 mA, f = 2 MHz  
VCE = −10 V, IC = −1 mA, f = 10.7 MHz  
Reverse transfer impedance  
22  
Reverse transfer capacitance  
(Common emitter)  
1.2  
pF  
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
2. : Rank classification  
*
Rank  
B
C
hFE  
70 to 140  
110 to 220  
Publication date: February 2003  
SJC00009BED  
1
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

NewAir Air Conditioner AC 12000E User Manual
Nikon Digital Camera WP CP3 User Manual
North Star Utility Trailer M268175D User Manual
Onkyo Stereo System HT RC270 User Manual
Oreck Air Cleaner ProShield Air Purifier User Manual
Oregon Scientific Clock RMR602A User Manual
Palsonic Air Conditioner A22R220 User Manual
Panamax Power Supply MAX 5410 User Manual
Panasonic Electric Shaver ER217 User Manual
Patton electronic Personal Computer 07M6070 UM User Manual