Optimus Stereo System 120 2180 User Manual

6 Disc CD Changer System  
(120-2180)  
Features  
Faxback Doc. # 17102  
The Optimus 6 Disc CD Changer System is a versatile, high-quality sound  
system that lets you load and play up to six of your favorite CDs in your  
vehicle. Providing the latest in sound technology, the CD changer has many  
practical, easy-to-use features and you can install it in almost any  
vehicle.  
You can operate many of the CD changer's functions with the supplied  
commander.  
IMPORTANT: The vehicle's sound system must have an FM tuner and an antenna  
jack for the CD changer to work with it.  
To be safe, we recommend you do not change the CD changer's or  
sound system's settings in heavy traffic or during hazardous  
driving conditions.  
The CD changer's features include:  
6-Disc CD Cartridge - Lets you load and play up to six CDs.  
3-Beam Laser Tracking - Improves the quality of the CD changer's  
System  
sound.  
Horizontal, 45-Degree, - Lets you easily and quickly install the CD  
or Vertical Mounting  
changer's components in almost any space in  
your vehicle.  
Spring-Loaded, Oil-Dampened - Helps keep the CD changer steady when you  
Suspension System drive over rough roads.  
Automatic Search Music - Lets you quickly locate the beginning of any  
System  
track while playing a CD.  
Audible Search - Lets you rapidly play a CD in either  
direction to locate a desired section of a  
track.  
Intro Scan - Scans and plays the first 10 seconds of each  
track on a CD, so you can find a specific  
track.  
Shuffle Play - Randomly selects and plays tracks from any  
 
6 Disc CD Changer System  
(120-2180)  
Installation  
Faxback Doc. # 17103  
BEFORE YOU BEGIN THE INSTALLATION  
Before you install the CD changer's components, read all the instructions  
in this owner's manual. You should be able to answer all of these  
questions about the vehicle's electrical and sound systems.  
Can my vehicle's sound system tune FM broadcasts?  
Does my vehicle's sound system have an antenna jack?  
Which terminal in my vehicle's fuse box is for accessories?  
How do I connect a wire to the fuse box?  
Which of the CD changer's wires is the power system?  
Does my vehicle have a 12-volt negative ground system?  
NOTE: Installation in your vehicle might require cutting or modifying  
your vehicle.  
In addition to the supplied hardware kit, you will need the following items  
to install the CD changer:  
Cable ties or electrical tape  
Isopropyl alcohol  
Small- and medium-sized Phillips screwdrivers  
CHOOSING/PREPARING THE MOUNTING AREAS  
The CD changer plays CDs through your vehicle's existing sound system. The  
supplied FM modulator converts the CD changer's sound to an FM signal so  
you can hear it by tuning your vehicle's stereo to an FM frequency. You  
use the supplied commander to control many of the CD changer's functions.  
Follow these steps before you mount the CD changer's components.  
1. Choose locations for mounting the CD changer and its components where:  
You can easily reach them.  
 
Wires and cables will not interfere with the vehicle's pedals or other  
moving parts.  
No component is directly in front of heating vents.  
All wires and cables will reach their connection points.  
2. Confirm that the CD changer and its components will fit the mounting  
areas you select.  
CAUTION: Be careful to avoid obstructions behind all mounting surfaces.  
CD CHANGER  
You can mount the supplied CD changer horizontally, at a 45-degree angle,  
or vertically in your vehicle's trunk, on the floorboard, or under a seat.  
CAUTION: Do not mount the CD changer upside down.  
NOTES: The CD changer's mounting area must be at least 13 inches (33 cm)  
deep.  
When you choose a mounting area for the CD changer, make sure it is  
close enough to the FM modulator's mounting area so you can connect  
both components with the supplied CD changer cable. The cable is  
about 16 feet (4.87 m) long.  
Do not mount the CD changer anywhere in your vehicle that is  
exposed to direct sunlight (such as the front or rear deck) or  
extreme heat (such as the engine compartment). Direct sunlight  
or extreme heat can damage CDs and the CD changer.  
Make sure your vehicle's mounting area is as level as possible. If  
you cannot mount the CD changer exactly level, make sure the CD  
changer will not tilt more than 15 degrees from the horizontal,  
45-degree, or vertical mounting positions.  
Make sure there is enough room for you to insert and remove the  
supplied CD magazine from the CD changer.  
FM MODULATOR  
You can mount the supplied FM modulator under your vehicle's dashboard.  
 
NOTES: The FM modulator's mounting area must be at least 7 inches  
(17.7 cm) wide by 3 1/4 inches (8.25 cm) deep.  
When you choose a mounting area for the FM modulator, make sure  
it is close enough to your vehicle's ground, power, and sound  
system so you can connect them with the FM modulator's wires and  
plugs (see "Making the Connections").  
COMMANDER  
For ease of use, you can mount the supplied commander on the dashboard  
using the supplied hook-and-loop fastening tape.  
NOTE: When you choose a mounting area for the commander, make sure it is  
close enough so the FM modulator's mounting area so the commander's  
cord will reach the FM modulator. The commander's cord is about 5  
feet (1.52 m) long.  
REMOVING THE SHIPPING SCREWS  
The shipping screws help protect the CD changer from damage during  
shipment.  
Before you mount the CD changer, use a small Phillips screwdriver to remove  
the four shipping screws from the bottom of the CD changer.  
CAUTION: If you do not remove the shipping screws from the CD changer,  
it will not work.  
HINT: Save the shipping screws in case you ever have to move the CD  
changer to another vehicle. You can secure them to the back of  
the CD changer with a piece of tape.  
 
6 Disc CD Changer System  
(120-2180)  
Connections  
Faxback Doc. # 17104  
Before you mount the CD changer and its components, test it by temporarily  
connecting all components, connecting the power wires, and connecting the  
FM modulator to your vehicle and your sound system.  
CAUTIONS: For added safety and to protect the CD changer and sound system,  
disconnect the cable from your vehicle battery's negative (-)  
terminal before you begin.  
You must make all other connections (as described in the  
following sections) before you reconnect the cable to your  
vehicle's battery. If you do not make the connections in the  
order shown, damage to the CD changer and sound system is  
possible if any wire connections are made incorrectly.  
CONNECTING THE FM MODULATOR  
The FM modulator includes all of the lead wires for connecting to your  
vehicle's ground, power, and sound system.  
1. Disconnect the cable from your vehicle battery's negative (-) terminal.  
2. Connect the black ground wire to a chassis ground, such as a metal  
screw attached to a metal part of the vehicle's frame. Be sure that  
the screw is not insulated from the chassis by a plastic part.  
3. Connect the red power wire (with in-line fuse holder) to a point in  
your vehicle's fuse block that has power only when you turn the  
vehicle's key to either the accessory (ACC) or start position.  
This connection turns on the CD changer and its components when you  
turn on the ignition or turn the key to ACC, and turns off the CD  
changer and its components when you turn off the ignition. This  
prevents your vehicle's battery from being drained if you leave the CD  
changer on when you turn off the ignition.  
4. Connect the yellow memory back up wire (with in-line fuse holder) to  
your vehicle battery's position (+) terminal or to a fuse that provides  
a continuous source of 12 volts.  
This connection provides power for the CD changer and its components,  
and continuous power for the CD changer's memory when the ignition is  
turned off.  
 
5. Disconnect your vehicle's antenna from your vehicle's sound system,  
then connect the antenna to the FM modulator's large black antenna  
connector.  
6. Connect the FM modulator's antenna plug to your sound system's antenna  
jack.  
CONNECTING THE CD CHANGER  
You connect the CD changer to the M modulator by inserting the straight  
plug on one end of the CD changer cable into the large jack on the FM  
modulator, then inserting the 90 degree plug on the cable's other end into  
the jack on the left side of the CD changer.  
CAUTIONS: The CD changer cable's plug fit only one way into the FM  
modulator and CD changer. Do not force them.  
To disconnect the CD changer cable from the FM modulator and  
CD changer, squeeze each plug, then gently pull it out.  
Never pull on the CD changer cable.  
CONNECTING THE COMMANDER  
To connect the commander to the FM modulator, insert the commander cable's  
plug into the small jack on the FM modulator.  
CAUTIONS: The commander's plug fits only one way into the FM modulator.  
Do not force it.  
To disconnect the commander from the FM modulator, gently  
pull it out.  
Never pull on the commander's cable.  
CHECKING THE CONNECTIONS  
Make sure you have securely made all connections before continuing with  
the installation, then reconnect the cable to the vehicle battery's  
negative (-) terminal.  
TESTING THE CONNECTIONS  
Verify that you connected the CD changer correctly by turning the CD  
changer correctly by turning the CD changer on and playing a CD. If  
 
everything is connected correctly, make sure the connections are correctly  
marked or identified. Then follow the instructions in "Mounting the CD  
Changer and Its Components."  
MOUNTING THE CD CHANGER AND ITS COMPONENTS  
Before you mount the CD changer and its components, be sure it is connected  
correctly. Then disconnect the cable from the vehicle battery's negative  
(-) terminal.  
Mounting the CD Changer  
1. Set H/45/V on both sides of the CD changer for the mounting axis you  
chose.  
H/45/V is preset to H (horizontal). If you are mounting the CD changer  
horizontally, leave H/45/V as it is and continue with Step 2.  
If you are mounting the CD changer at a 45-degree angle, use a small  
Phillips screwdriver to remove the screw from H, use the supplied tool  
to turn H/45/V to 45 (45-degree angle), then replace the screw into 45  
on both sides of the CD changer.  
If you are mounting the CD changer vertically, use a small Phillips  
screwdriver to remove the screw from H, use the supplied tool to turn  
H/45/V to V (vertical), then replace the screw into V on both sides of  
the CD changer.  
CAUTION: If you do not set H/45/V on both sides of the CD changer to  
the correct mounting axis, the CD changer might skip during  
play.  
HINT: Save the tool in case you ever want to install the CD changer in  
another vehicle or change the mounting location. You can secure  
it to the back of the CD changer with a piece of tape.  
2. Use a medium-sized Phillips screwdriver to attach the supplied  
mounting brackets to the sides of the CD changer.  
If you are mounting the CD changer horizontally, attach both mounting  
brackets to the CD changer.  
If you are mounting the CD changer at a 45-degree angle, attach both  
mounting brackets to the CD changer.  
If you are mounting the CD changer vertically, attach both mounting  
 
brackets to the CD changer.  
3. Using the supplied mounting studs as templates and the width between  
the mounting brackets as a guide, mark the positions for the mounting  
holes.  
4. Attach the mounting studs to the mounting surface using the supplied  
screws.  
5. Attach the CD changer to the mounting studs using the supplied wing  
nuts.  
MOUNTING THE FM MODULATOR  
1. Use the supplied screws to attach the FM modulator under the vehicle's  
dashboard.  
2. Use cable ties (not supplied) to secure the FM modulator's wires  
under the dashboard.  
MOUNTING THE COMMANDER  
The supplied hook-and-loop fastener lets you securely mount the commander  
on the dashboard and easily remove it when you need it.  
Determine the commander's exact mounting location. Then follow these  
steps to secure the commander.  
1. Clean both mounting surfaces with isopropyl alcohol and allow them  
to completely dry.  
2. Peel the backing off one piece of the hook-and-loop fastener and press  
it onto the back of the commander.  
3. Peel the backing off the other piece of the hook-and-loop fastener  
and press the commander onto the desired location.  
RECONNECTING THE VEHICLE'S BATTERY  
Reconnect the cable to the vehicle battery's negative (-) terminal.  
SETTING THE FM FREQUENCY  
Set 88.7 MHz/88.3 MHz on the side of the FM modulator to an active  
frequency in your area, if available. This is the frequency you tune to on  
your vehicle's sound system to hear the CD changer.  
 
NOTE: If there is no FM broadcast on either 88.7 MHz or 88.3 MHz in your  
area, you might hear static when the CD changer is not playing a CD.  
If this occurs, be sure to lower your radio's volume before the CD  
stops.  
CHANGING THE DISPLAY'S COLOR  
The display's color is preset to green. Repeatedly press LIGHT until the  
display shows the color you want (green or amber).  
 
6 Disc CD Changer System  
(120-2180)  
Operation  
Faxback Doc. # 17105  
LOADING AND UNLOADING CDS  
You can load as many as six CDs in the supplied CD magazine.  
CAUTION: Play only CDs that have this mark on them:  
1. Hold the CD magazine so that clear CD window faces you and the highest  
CD number (6) is at the top of the CD window.  
2. Slide all of the disc levers on the back edge of the CD magazine to the  
left.  
3. To insert a CD, slide it onto any of the exposed slots on the right  
side of the CD magazine, label side up. Then gently press the CD to  
the left until it locks.  
As you insert a CD into the CD magazine, its disc lever moves to the right.  
CAUTIONS: Do not insert more than one CD into the same slot in the CD  
magazine. This could damage the CD magazine, the CD changer,  
and the CDs.  
Do not insert anything other than 5-inch CDs in the CD magazine.  
To unload CDs from the CD magazine, press and hold down the disc lever for  
the CD you want to unload. The CD sticks out slightly. Grasp the CD by  
its edges and remove it.  
LOADING AND UNLOADING THE CD MAGAZINE  
Follow these steps to load the CD magazine into the CD changer.  
1. Slide the CD changer's door all the way to the right to open it.  
2. Hold the CD magazine so the clear CD window faces you and the highest  
CD number is at the top of the CD window, then gently push it into the  
CD changer until it clicks.  
CAUTION: The CD magazine fits into the CD changer only one way. Do  
not force it.  
3. Slide the CD changer's door all the way to the left to close it.  
 
To unload the CD magazine from the CD changer, slide the CD changer's  
door all the way to the right to open it, then press UP ARROW.  
PLAYING CDs  
CAUTIONS: The CD changer has a wide dynamic range. If you turn up your  
radio's volume too high during soft (low volume) sections of a  
program, your speakers might be damaged when a sudden loud  
passage occurs.  
If the CD changer is jolted during play, the rotation speed  
might suddenly change or the CD changer might make an unusual  
noise. This is not a malfunction.  
NOTE: To play CDs, you must load them into the CD magazine, then load the  
CD magazine into the CD changer.  
1. When you turn on your vehicle's ignition and press ON on the commander,  
it's display turns on, and - -- flashes for a few seconds. Then LOAD  
flashes as the CD changer displays the number for each CD loaded in the  
CD magazine (6-1), starting with the CD you loaded into the highest  
slot number. Then the CD changer selects the CD you loaded into the  
lowest slot number.  
NOTE: - -- continues to flash if you did not load CDs into the CD  
magazine, or did not load the CD magazine into the CD changer.  
2. Turn on your vehicle's sound system, select the radio's FM band, then  
tune the radio to the same FM frequency as the 88.3 MHz/88.7 MHz  
setting on the FM modulator.  
HINT: Store this setting as one of your sound system's FM stations.  
3. Press >||. The CD starts to play from Track 1, and the display shows  
DISC and the lowest loaded CD number, TRACK and 01, and the elapsed  
time of Track 1.  
After the CD changer plays each track on the CD, it automatically  
selects the next loaded CD (from lowest to highest) and plays all  
tracks on that CD, starting with Track 1.  
After the CD changer plays all tracks on all loaded CDs, it  
automatically plays the lowest loaded CD, starting with Track 1. Play  
continues until you stop the CD changer.  
 
4. Adjust your sound system's volume and tone controls as desired.  
NOTE: To pause playback, press >||. To resume playback, press >||  
again.  
5. To stop playback and turn off the CD changer, press OFF.  
AUTOMATIC SEARCH MUSIC SYSTEM (ASMS)  
To move to the beginning of the next or previous track on the CD, press  
|<< or |>> once. To move to the beginning of other tracks on the CD,  
repeatedly press |<< or >>| until the display shows the desired track  
under TRACK.  
AUDIBLE SEARCH  
To search for a particular section of a track on the current CD, press and  
hold down << or >> during play. The CD changer rapidly plays the CD either  
backward or forward. When you hear the section you want, release << or >>  
to resume normal play.  
SELECTING A SPECIFIC CD  
To select a particular CD in the CD magazine, repeatedly press DISC during  
play until the display shows the desired CD number under DISC. The CD  
changer stops playing the current CD (if it was playing one), then plays  
the new CD.  
INTRO SCAN  
You can set the CD changer to play the first 10 seconds of each track on  
the current CD, so you can find the desired track.  
To begin scanning, press SCAN during play. The display shows SCAN.  
To stop scanning and resume playback, press SCAN again. SCAN disappears  
from the display.  
REPEAT PLAY  
To repeat a track on the current CD, press REPEAT while that track is  
playing. The display shows REPEAT. When the track ends, it automatically  
repeats.  
To stop repeating the track, press REPEAT again to resume normal play.  
REPEAT disappears from the display.  
 
SHUFFLE PLAY  
You can set the CD changer to randomly select and play tracks from the  
current CD. After one track plays, the CD changer automatically selects  
another track and plays it until you stop shuffle play.  
To begin shuffle play, press SHUFF. The display shows SHUFF.  
To stop shuffle play, press SHUFF again to resume normal play. SHUFF  
disappears from the display.  
SWITCHING BETWEEN CD/RADIO  
You can listen to the radio while a CD is playing by tuning the radio to  
the station you want to hear.  
NOTE: The CD continues to play while you listen to the radio.  
To return to the CD, tune the radio to the same FM frequency as the 88.3  
MHz/88.7 MHz setting on the FM modulator.  
 
6 Disc CD Changer System  
(120-2180)  
Troubleshooting  
Faxback Doc. # 17106  
If your CD changer is not working as it should, these suggestions might  
help you eliminate the problem. If the CD changer still does not operate  
properly, take it to your local Radio Shack store for assistance.  
SYMPTOM  
POSSIBLE CAUSE  
Power problem.  
SUGGESTION  
No power-display  
does not light  
after vehicle power  
Check the CD changer's  
and sound system's  
fuses and replaces  
them if necessary.  
is turned on.  
CD changer/components  
not connected to sound  
system/vehicle correctly.  
Check all connections.  
No sound.  
Vehicle radio's volume  
set to minimum.  
Adjust the vehicle  
radio's volume.  
Vehicle radio not  
set to the proper  
FM frequency.  
Set vehicle radio to  
FM band and tune to  
frequency set on FM  
modulator (88.3 MHz or  
88.7 MHz).  
CD changer/components  
not connected to sound  
system/vehicle correctly.  
Check all connections.  
CD changer does not  
work.  
Shipping screws not  
removed from CD  
changer.  
Remove the shipping  
screws from the CD  
changer.  
No CDs loaded in CD  
magazine.  
Load CDs in CD  
magazine.  
CD magazine not  
loaded in CD  
changer.  
Load CD magazine in  
CD changer.  
CD loaded upside  
Load CD correctly.  
down in CD magazine.  
 
CD is dirty or defective  
Clean the CD or try  
another CD.  
CD changer must be  
reset.  
Reset the CD changer.  
Sound from CD skips.  
CD is dirty or defective.  
Clean the CD and try  
it again, or try  
another CD.  
H/45/V set incorrectly.  
Check H/45/V on both  
sides of CD changer  
and reset if  
necessary.  
Static sounds on  
radio when CD  
stops playing.  
FM modulator not set  
to a frequency with an  
active radio station.  
Set 88.3 MHz/88.7 MHz  
to a frequency with an  
active station (if  
available).  
NOTE: If there is no active  
broadcast on 88.3 MHz  
or 88.7 MHz, you  
cannot eliminate  
these static sounds.  
CD magazine does not  
eject from CD changer power to eject CD  
when UP ARROW is  
pressed.  
CD changer requires  
Turn on your vehicle's  
ignition and try  
again.  
magazine.  
Check the CD changer's  
and sound system's  
fuses and replace them  
if necessary.  
 
6 Disc CD Changer System  
(120-2180)  
Hints and Tips  
Faxback Doc. # 17107  
Even though a CD is very durable, you should handle it with care. We  
recommend the following precautions.  
Keep the CD in its protective case or sleeve when you are not playing  
it.  
Handle a CD by its edges to avoid fingerprints which can prevent the  
CD changer's laser beams from accurately reading the CD. Your local  
Radio Shack store sells a suitable CD cleaner kit.  
Do not Write on either side of the CD, particularly the non-label  
side. (Signals are read from the non-label side.)  
Keep the CD dry. A water drop can act as a lens and affect the laser  
beam's focus.  
If you park your vehicle in the sun, temperatures inside the vehicle  
can easily reach levels that could damage your CDs. To prevent heat  
damage, avoid leaving your CDs in your vehicle.  
If a CD skips when you play it, the CD might be scratched. Your local  
Radio Shack store sells a Scratch 'n Fix kit (Cat. No. 42-127) that  
might help remove the scratch and stop the skip.  
RESETTING THE CD CHANGER  
If your CD changer or any component locks up or does not work properly,  
or if the vehicle's battery loses power, follow these steps to reset the  
CD changer.  
1. Turn on your vehicle's ignition.  
2. Slide the CD changer's door all the way to the right to open it.  
3. With a pointed object, such as a straightened paper clip, press the  
reset hole (to the left of UP ARROW inside the CD changer) for about 2  
seconds.  
REPLACING A FUSE  
If the CD changer or its components do not operate, you might need to  
replace the red power wire's or yellow continuous power wire's fuse with  
 
one of the supplied fuses. Check both fuses.  
WARNING: Before you begin, disconnect the cable from the vehicle battery's  
negative (-) terminal.  
1. Unlatch the two latches on the fuse holder so the holder springs open.  
2. If either fuse is blown, replace it. Use only standard 1 1/4-inch  
fuses with the proper rating. The red power wire's fuse must be 1.0  
amp, and the yellow continuous power wire's fuse must be 2.0 amps.  
CAUTION: The supplied spare fuses have the proper ratings. Make sure  
you replace a fuse only with another fuse of the same rating.  
3. Reassemble the fuse holder only squeezing it together.  
4. Reconnect the cable to the vehicle battery's negative (-) terminal.  
 
6 Disc CD Changer System  
(120-2180)  
Specifications  
Faxback Doc. # 17108  
CD CHANGER  
Frequency Response:  
40 Hz:..........................................................+/-2 Hz  
10 kHz:..........................................................-10 Hz  
16 kHz:...........................................................60 dB  
Signal-to-Noise Ratio (1 kHz):.......................................60 dB  
Harmonic Distortion (1 kHz):............................................3%  
Signal Format:  
D-A Conversion:...................................2-Channel Sigma Delta  
Sampling Type/Frequency:.....................8 x Oversampling, 44.1 kHz  
Pick-Up:  
System:...........................................Sony KSS-320B, 3-Beam  
Wavelength:..................................................760-800 nm  
CD Used (Diameter):........................................5-inch (120 mm)  
Power Source:................................14.4 Volts DC Negative Ground  
Power Consumption:.............................................3 A Maximum  
Unit Weight:...........................................6 lbs 7 oz (2920 g)  
Unit Dimensions:...................11 11/32 x 2 29/32 x 7 3/8 Inches (WHD)  
(288 x 74 x 187.5 mm)  
COMMANDER/FM MODULATOR  
Power Source:................................14.4 Volts DC Negative Ground  
Unit Weight:  
Commander:.........................................4.2 Ounces (0.12 Kg)  
FM Modulator:.....................................13.7 Ounces (0.39 Kg)  
Unit Dimensions:  
Commander:...............................3 1/2 x 27/32 x 3 Inches (WHD)  
(89 x 20 x 76 Millimeters)  
FM Modulator:.................. .......5 1/4 x 1 1/18 x 3 1/4 Inches (WHD)  
(144 x 28 x 82 Millimeters)  
Specifications are typical: individual units might vary. Specifications  
are subject to change and improvement without notice.  
 
Audio Connection Information  
(120-Series)  
Plug/Male 2 Ch. System  
Faxback Doc.# 19994  
+----+--------------+---------------+------------+------------------------+  
|Pin |  
|
|
|
|
|
|
|No. | WIRE COLOR | WIRE SPECS. | LABEL  
REMARK  
+----+--------------+---------------+------------+------------------------+  
| 1 | WHT/BLK  
| AWG #20  
| 2P CORD  
| FRONT L- | STRIP SOLDER  
|
|
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
| 2 | GRY/BLK | FRONT R- |  
+----+--------------+---------------+------------+------------------------+  
| 3 |  
+----+--------------+---------------+------------+------------------------+  
| 4 |  
+----+--------------+---------------+------------+------------------------+  
| 5 | BLACK | AWG 206 | GROUND | 6.3mm r FORK TERMINAL |  
+----+--------------+---------------+------------+------------------------+  
| 6 | ORG/WHT * | | DIMMER | STRIP SOLDER  
+----+--------------+---------------+------------+------------------------+  
| 7 | PINK/WHT * | | PHONE MUTE |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
|
|
|
|
|
|
|
"
|
"
"
|
| 8 | WHITE  
| AWG #20  
| 2p CORD  
| FRONT L+ |  
|
|
|
|
|
|
"
+----+--------------+---------------+------------+------------------------+  
| 9 | GRAY | FRONT R+ |  
+----+--------------+---------------+------------+------------------------+  
| 10 |  
+----+--------------+---------------+------------+------------------------+  
| 11 |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
|
|
|
|
|
|
|
RED  
| AWG #20  
|
| +12 V TO | 250/ 1A FUSE & 24M/M |  
| IGNITION | TRANS STRIP SOLDER |  
+----+--------------+---------------+------------+------------------------+  
| 13 | YELLOW  
|
|
"
| +12 V TO | 250/ 1A FUSE STRIP  
| BATTERY | SOLDER  
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
| 14 | DARK BLUE/ |  
"
| AMP REMOTE | WIRE BANDING &  
|
|
|
|
|
|
|
|
|
|
|
|
|
WHITE  
|
|
|
|
| TURN ON |  
| 500mA MAX |  
|+12 V OUTPUT|  
TUBE HEATING  
|
|
+----+--------------+---------------+------------+------------------------+  
* May or may not be present depending on features of individual radios.  
 
(2CH/4CH SWITCHABLE UNIT)  
+----+--------------+---------------+------------+------------------------+  
|Pin |  
|
|
|
|
|
|
|No. | WIRE COLOR | WIRE SPECS. | LABEL  
REMARK  
+----+--------------+---------------+------------+------------------------+  
| 1 | WHT/BLK  
| AWG #20  
| 2P CORD  
| FRONT L- | STRIP SOLDER  
|
|
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
| 2 | GRY/BLK | FRONT R- |  
+----+--------------+---------------+------------+------------------------+  
| 3 | GRN/BLK | REAR L- |  
+----+--------------+---------------+------------+------------------------+  
| 4 | VIO/BLK | REAR R- |  
+----+--------------+---------------+------------+------------------------+  
| 5 | BLACK | AWG 206 | GROUND | 6.3mm r FORK TERMINAL |  
+----+--------------+---------------+------------+------------------------+  
| 6 | ORG/WHT * | | DIMMER | STRIP SOLDER  
+----+--------------+---------------+------------+------------------------+  
| 7 | PINK/WHT * | | PHONE MUTE |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
"
"
|
|
"
"
|
"
|
"
"
|
| 8 | WHITE  
| AWG #20  
| 2p CORD  
| FRONT L+ |  
|
|
|
|
|
|
"
+----+--------------+---------------+------------+------------------------+  
| 9 | GRAY | FRONT R+ |  
+----+--------------+---------------+------------+------------------------+  
| 10 | GREEN | REAR L+ |  
+----+--------------+---------------+------------+------------------------+  
| 11 | VIOLET | REAR R+ |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
"
|
|
"
"
|
| 12 |  
RED  
| AWG #20  
|
| +12 V TO | 250/ 1A FUSE & 24M/M |  
| IGNITION | TRANS STRIP SOLDER |  
|
|
+----+--------------+---------------+------------+------------------------+  
| 13 | YELLOW  
|
|
"
| +12 V TO | 250/ 1A FUSE STRIP  
| BATTERY | SOLDER  
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
| 14 | DARK BLUE/ |  
"
| AMP REMOTE | WIRE BANDING &  
|
|
|
|
|
|
|
|
|
|
WHITE  
|
|
|
| TURN ON |  
| 500mA MAX |  
|+12 V OUTPUT|  
TUBE HEATING  
+----+--------------+---------------+------------+------------------------+  
* May or may not be present depending on features of individual radios.  
4 Chnl Unit  
+----+--------------+---------------+------------+------------------------+  
 
|Pin |  
|
|
|
|
|
|
|No. | WIRE COLOR | WIRE SPECS. | LABEL  
REMARK  
+----+--------------+---------------+------------+------------------------+  
| 1 | WHT/BLK  
| AWG #20  
| 2P CORD  
| FRONT L- | STRIP SOLDER  
|
|
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
| 2 | GRY/BLK | FRONT R- |  
+----+--------------+---------------+------------+------------------------+  
| 3 | GRN/BLK | REAR L- |  
+----+--------------+---------------+------------+------------------------+  
| 4 | VIO/BLK | REAR R- |  
+----+--------------+---------------+------------+------------------------+  
| 5 | BLACK | AWG 206 | GROUND | 6.3mm r FORK TERMINAL |  
+----+--------------+---------------+------------+------------------------+  
| 6 | ORG/WHT * | | DIMMER | STRIP SOLDER  
+----+--------------+---------------+------------+------------------------+  
| 7 | PINK/WHT * | | PHONE MUTE |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
"
"
|
|
"
"
|
"
|
"
"
|
| 8 | WHITE  
| AWG #20  
| 2p CORD  
|
|
|
|
"
+----+--------------+---------------+------------+------------------------+  
| 9 | GRAY | FRONT R+ |  
+----+--------------+---------------+------------+------------------------+  
| 10 | GREEN | REAR L+ |  
+----+--------------+---------------+------------+------------------------+  
| 11 | VIOLET | REAR R+ |  
+----+--------------+---------------+------------+------------------------+  
|
"
"
|
|
"
|
|
"
"
|
| 12 |  
RED  
| AWG #20  
|
| +12 V TO | 250/ 1A FUSE & 24M/M |  
| IGNITION | TRANS STRIP SOLDER |  
|
|
+----+--------------+---------------+------------+------------------------+  
| 13 | YELLOW  
|
|
"
| +12 V TO | 250/ 1A FUSE STRIP  
| BATTERY | SOLDER  
|
|
|
|
+----+--------------+---------------+------------+------------------------+  
"
| AMP REMOTE | WIRE BANDING &  
|
|
|
|
| TURN ON |  
| 500mA MAX |  
|+12 V OUTPUT|  
TUBE HEATING  
+----+--------------+---------------+------------+------------------------+  
* May or may not be present depending on features of individual radios.  
5-Pin DIN  
FRONT  
+---------+--------------+  
| Green | Right (+) |  
 
+---------+--------------+  
| White | Right (-) |  
+---------+--------------+  
| Brown | Left (+)  
+---------+--------------+  
| Gray | Left (-)  
+---------+--------------+  
| Red | +12 V Power |  
|
|
+---------+--------------+  
REAR  
+---------+--------------+  
| GRN/BLK | Right (+)  
+---------+--------------+  
| WH/BLK | Right (-)  
+---------+--------------+  
| BR/BLK | Left (+)  
+---------+--------------+  
|GRAY/BLK | Left (-)  
|
|
|
|
+---------+--------------+  
+---------+--------------+  
| Orange | S.P.L.  
+---------+--------------+  
| Black | Ground  
+---------+--------------+  
|
|
| Red w/ | Memory  
| White | Backup  
|
|
+---------+--------------+  
(/ir-10/08/96)  
LN-03/04  
 

MTD Lawn Mower 111 902 026 User Manual
National Instruments Table Top Game 370769C 01 User Manual
NETGEAR Switch FS105 V2 User Manual
Nokia Cell Phone 252 User Manual
Oki Printer 58372901 User Manual
One for All Universal Remote 5 User Manual
Onkyo Universal Remote RC 482M User Manual
Oreck Binoculars BIN25 User Manual
Oregon Scientific Games 086L004850 017 User Manual
Panasonic Projector PT AX100E User Manual